JKS05V1AD General Electric Wall Oven - Instructions

After getting the part from PartSelect, which only took 2 days to get here and was in great condition and matched perfectly. I went to the customers house, shut off the power to the oven, removed the 2 screws holding in the element, pulled the element out and removed the leads. Took the new element and put the leads on the contacts, pushed the wires and leads back into the hole and screwed in the 2 screws. Went outside and turned the breaker back on, went and turned the oven on to broil, waited a few seconds and it heated up perfectly, and the customer was real happy. She said it was great that she could bake again. Thank you guys for sending the right part in a timely manner and good condition, it keeps my customers happy and keeps me in business. Joe

Pull door from oven and place on flat work surface. Remove bottom screws then the top screws and separate the two halves of the door . Remove broken door handles and replace reassemble door and place back on oven. The hardest thing was to clean the grease out of the inside of the door and get the glass clean to reassemble the door.

First of all, go to circuit breaker box and switch off the power to the oven.

Return to oven and verify the power is definitely off.

Open oven door to 'vent' position and remove door. Return hinges to closed position. Remove all racks.

Using nut driver (1/4-inch) remove the two screws just above the element.

Gently rock the element back and forth while pulling gently toward yourself. You should see two wires emerging from the layer of insulation in back of oven. When you have enough wire exposed, use long-nose pliers to gently rock the 'Faston' connectors and pull them off the element's male connectors.

Insert new element and re-install the connectors, being certain they are fully engaged.

Fasten the new element to the back wall of the oven using nut driver. Be careful to not cross-thread - gentle is the word!

Turn the circuit breaker on and very briefly turn the oven to Bake and verify the element is heating. It likely will smoke a bit.

Re-install the racks and the door. Reset the clock.

You should be done and your oven should run for many years..

Slide oven door off slides and put oven door on table. Removed 2 torx-20 screws from top of oven door on the inside. Remove 4 sheet medal screws from the bottom of door 1/4' socket heads. The inside of the door will now separate from the front of door.Now you can see 2 screws on each side of the door handle end caps on 1/4 " socket heads. Remove the 2 screws on which ever side is broken and remove old end cap and side new one on an install 2 screw. When you put door back together there are 2 spring steel spacers that fall off the top 2 screws that hold the inside and outside at the proper space! Parts Select service is EXCELLENT!!!!!

The whole job took about 20 min. TURN POWER OFF AT CIRCUIT BREAKER!! Remove 4 screws from the convection cover, then 2 more holding in the broiler element, disconnect 2 wires, and connect to the new one. put the screws back in, the cover back on the convection element and you are done!

Took the 3 knobs out of the bag and slid them on . Perfect fit no problems.

had two screws to remove from old element, than removed two electric wires from the old element and put the new element back in by putting the wires on the new element and reinstalling the element back in place with two screws and it was done. took about 5 mins. to complete. easy.

Turn off breaker to oven from electrical panel, locatge all screws and remove. Use caution when removing element from clips if not replacing the clips. When removing the element, be careful not to damage connecting wires as they do not pull out very far. Be sure to reattach correctly. When replacing the oven seal, be careful not to disconnect the wires to either element as you slide the oven compartment forward after removing screws. It can be difficult to find the wires behind the oven compartment if they disconnect.

Removed door from oven. Removed all side screws and pulled front assembly from door. Discarded old screws and broken plastic pieces. Put old handle in new end caps and lined them up with screw entry holes. It took 2 people to hold the door up while pressing in the screws to enter the new plastic receivers on the end caps. A pretty easy fix.

Pulled out old with pliers. Twisted new clips in per instructions.

I tried to unplug old element without success. Called appliance repair man and he pulled part way out, took hold of place where plugged in with pliers and unplugged. While holding back part of plug he plugged in new element--$60.00 later.

Removed the door and four screws to get to handle. Removed the two screws holding the handle and replaced with new handle. Replaced the four screws on the door and reconnected to oven.