JTP15BW1BB General Electric Wall Oven - Instructions

Quick and easy, thanks!

#1) Found electrical control breaker and moved to "off" position

#2) Removed two (2) screws with a nut driver, that were holding the bake element in position against the back wall of the oven. Gently pulled the original bake element out toward the door to expose the wire connectors from oven to element, then disengaged the connections.

#3) Removed the damaged element, replaced with the new element, reconnected the wires to the element, and returned same into the back wall opening and reinserted the two (2) screws with nut driver.

Repair was complete. Electrical breaker returned to on. Procedure Done!

1. Open oven door
2. insert oven racks (perfect fit)
3. close oven door. Done and finished - man am I tired

Took door off of hinge
Removed 6 screws from bottom of door
Removed glass
Removed screws from side of door
Removed door from frame
Replaced the end caps using exisiting screws
Put door back together in reverse order
Pretty easy but simple instructions would have made it a 15 minute job instead of 30

Parts Select is the only parts place I found on the internet that had what I needed on my first purchase, so when I needed these clips I naturally went back to them. Product was easy to find, price was fine, receipt for payment quick and more importantly receipt of item was super quick. Thanks to the efficiency of this place and my old appliances, I will continue to go to them as needed.

Open door lift door off hinges lay door face down on flat surface remove 6 phillip head screws 3 on each side lift housing out of door case remove end knob phillip head screws installed one knob insert bar attch second knob and tighten screws lay housing back into casing attach screws doing one at a time on each side slide door back on to hinges and test operate, you are done!

remove the screws, replaced the element, replaced the screws.

Step #1: Remove 2 screws at the inside top of the oven door that holds the inner/outer oven door together. Step #2: Remove the screws from the inner door that hold the plastic handle end caps to the door. Tip: Use a file to dress up the tips of the metal handle bar so that it fits easily into the new plastic handle end caps. Step #3: Install the first new plastic handle end cap. Step #4: Slide the metal handle bar into the plastic handle end cap that was just installed on the outer oven door. Step #5: Place the other plastic handle end cap on the metal handle bar. Step #6: Install the second plastic handle end cap on the outer oven door. Step #7: Reassemble the oven door by installing the screws that were removed in step #1.

The first task is to turn off the breaker so there is no power coming to the oven. I learned in the hard way that even though the oven is turned off, there is still a hot wire connected to the bake element. Next,I removed the oven door and shelves. Then I used a nutdriver to remove the two screws holding the element in place. I expected to find a plug, however the element is connected to two wires buried in the insulation. I pulled the wires off of the bake element, connected them to the new element and put everything back together. This is not a difficult task.

Initially replaced thermostat sensor but unsuccessful. With some help from internet repair, the removal and replacement of the electronic board was easy given the labelling on the new board was essentailly identical to older model.

First I unplugged unit. Theni removed the two screws that hold the element in place . Then went to pull the element out to disconnect the two wires,but was having alittle trouble. There for I removed the large plate(cover) on the back of range,and removed the wires from this location. Put the new element in place,reattached wires,screwed back plate back on ,and pluged back in.

Repair was basically simple. Remove 6 screws holding door facing on door, remove one screw holding handle end caps in place. Then reverse the operation installing handle end caps. The problem I had was that the new a end caps had different dimensions than the old ones and the handle wouldn't slip into them. Had to carve away material inside the new caps with an exacto knife in order to fit the handle. The result was a 15 minute job took well over an hour

I took the old cap off, and replaced it with the new one. I am glad I had the sense to buy this online, If I had gotten a repairman to fix this, it probably would have costs $100.00 instead of the $17.00 it cost me to fix it myself. Thanks.

Dislodged screws to oven door to get to handle assembly. Fairly easy, however, new door handle end caps do not come with screws and the old screws were not a good fit. Almost stripped the old screw trying to get it in place. Strongly suggest that Part Select send replacement screws with handle to facilitate repair. Door handle is back up but is now loose until I can find/secure appropriate replacement screws and repeat the process all over again.

It took longer to go and buy the star tool then the repair. If you have the tools close it is a ten minute repair....