PLEB30T8CCB Frigidaire Wall Oven - Instructions

The repair was simple; first I removed the 2 screws from the old element and disconnected the wires and then I inserted the new element reconnected the wires and replaced the screws . The repair was easy and took less that 15 min. The oven works as good as new and I saved alot of money by doing it myself.

Replaced clock control by removing surface burner control knobs and plastic nuts, and then the cover over the oven control. Two screw hold the clock in place, after removal and disconnecting the plug-in you can reinstall the new clock control. The Heat Sensor inside the oven will also need to be replaced. It is located inside the oven and attached with two screws; the back of the oven will need to be removed to unplug. Reverse removal procedure and turn the power back on to the stove.

I pulled my unit out of the wall and noticed that the insulation around the top broiler element was a bit brown. Closer inspection revealed that the element had shorted somehow to the oven itself and caused the element to become non-functional. I tried measuring the resistance first, and it was within typical values for the other elements, but I decided to replace the element anyway.

I ordered from PD and the part arrived just a few days letter by regular shipping. I undid the screws holding in the element, undid the wire connectors and replaced the broken element with the new one. The element worked like a charm and I was back in business for cooking.

PF alarm appeared on display. Noticed clicking when cord was moved. Had arced for some time and melted original block. New part slightly different. Only has 3 lugs, old one had six. Stack using washers provided. Take note of colors before disassembly. Use caution while working through access opening. The edges are sharp. Only tools needed are phillips screwdriver, deep socket for lug nuts. Nut driver optional. Hope this is helpful.

PartsSelect serivce was AMAZING - I ordered online on Sunday afternoon, and the part arrived Tuesday with standard shipping! First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires from the old element, then replaced with new. WARNING - you MUST kill the breaker, because the element is "hot" even when it's off.

Turned power off at electrical panel. Pulled oven away from wall. Removed back cover (6 screws), then unplugged wires from old receptacle. I had to pull the squeeze clips backwards & break them to remove the old receptacle - couldn't squeeze them enough to remove them otherwise. The old receptacle came out through the inside of the oven, and the new one snapped in easily from inside the oven as well. Replaced wiring, installed new bulb, restored power & tested. Replaced back cover. Good time to vacuum under/behind where the oven usually lives before sliding it back to the wall.

I removed the two screws and then used pliers to pry apart the wiring. I unplugged the connectors and removed the element. The new unit arrived in three days and I plugged it in, replaced the screws and turned the oven on and made a pie! Very Satisfying and easier then I ever thought it would be. We figured we saved $200.00. The service place where we live charges $125.00 to come out and assess and then parts and service on top of that.

Took out the bad element and replaced it with the new element in less than 5 minutes. Simple Stuff with the right part. Thanks Parts Select!

Easier than painting my toenails!! The gasket came out easily just by pulling with my hands. Replacing it with the new one was even simpler. The clips are already attached to the gasket and easily slip into the holes on the door. I used the end of a tupperware orange peeler to push the unfinished ends of the gasket into a slot at the bottom and that was it! A new, perfect seal and it looks and works great!

I looked online and read what other people had done. The best advice was keeping all the screws in the order they were taken out. I also separated the screws that had come from the top, sides and inner side of the door. This helped immensely as I reassembled the door. I spread out a heavy garbage bag that I cut open. This kept debris and glass off of my kitchen floor. This is NOT a difficult repair; Parts Select said it would take three days to get me the glass; it arrived in TWO! Start to finish, the entire job took just about an hour. I saved myself over $100, and again, this is NOT difficult!

Removed two screws holding broiler element. Released two spring hangers on near the front of the element. Pulled element away from oven and pulled two wire connectors off. Simply reverse process to install new one. Wasn't the problem.

Removed electrical connector and two screws. Attached the electrical connector to the new probe and attached with the two screws.

Based on previous responses we anticipated this repair to be easy, however, it was a little more challenging than expected. The method of repair was easy enough, just would have been better if there had been more wire to pull out to connect to the new bake element. It took two of us to fish for the wires back inside the stove with a needle-nose pliers after removing the element. One had to hold the wire with the pliers while it took the other to attach it to the new element with second pair of pliers as there was no room for using fingers. Retrieving and attaching the second wire to the element was even more challenging because now the half-attached element was in the way. Disappointed and not sure why the element burned out in the first place on a 4year old appliance.

Pull old switches out with pliers and replugged new switches. On main oven, plug casing was melted (wife left broiler on with oven door closed) so had to break apart old casing and individually plug the the wires into new switch and amazingly, it worked! Just gotta keep the door open when broiling.............

1. SHUT OFF POWER TO YOUR RANGE! (I flipped the circuit breaker at the box to do this. To be totally safe, you can shut off the power to the whole house.) 2. Remove the oven racks. 3. Undo the two screws (save for step 8) holding the bake element in place. (This took some doing for me, as the screws did not want to come out easily. Maybe use some penetrating oil and be careful not to strip the screws.) 4. Gently pull the bake element toward you, exposing the contacts and wires. 5. Remove the wires from the old element's contacts. (Remember which contact 6. Attach the wires to the new element's contacts. 7. CAREFULLY push the wires back into the wall of the oven. (Pay attention to the insulation. Make sure that some insulation is near the wall.) 8. Fasten element to wall of oven with screws you saved from step 2.