KUCS03CTSS2 KitchenAid Trash Compactor - Instructions

replaced rotatory switch (10mins) problem solved

Removed bottom and replaced gears

After inspecting to make sure the actuator was functional and that power to the unit was not an issue I was able to find that one the drive gears cracked in half and made the compactor inoperable. It was easy to remove the bottom casing with a nut driver. This casing covered the drive gear which operated the ram. After slightly loosening the gear mounts and I was able to replace center gear and re-attach gear chain and re-tighten. Then replace bottom casing and the compactor was back in action. Huge savings!

Removed the gear cover at the bottom of the compactor. Loosened the slack on the chain. Replaced the gear drive. Replaced the gear cover. Worked like new. No major obstacles.

shook bottle and painted waited a day and repeated

the bearing were the perfect match and instructions helpful. sysem is rolling smoothly

I read the Parts Select trouble shooting guide which indicated that 99% of the time the problem was with the Directional Switch so I ordered one. I pulled the unit out from under the countertop, unplugged the electrical plug from the outlet and took the trash tray out of the unit and set it aside. I took the top panel off with the nutdriver as well as the front panel along with the handle of the power switch. Better access to the Directional Switch can be made by removing the compacting unit. This can be done by sliding it up out of appliance and setting it aside. I used a phillips screw driver to unscrew the two screws on the right side of the switch and the two thin compression plates on the left side which hold the switch in place. I then carefully removed the contact wires from the Directional Switch one at a time and placed them on the new switch in the proper locations. The switch can then be reinstalled with the screws and compression plates. The compacting unit can then be loaded back into the appliance with the activating bracket to the front, BUT be very careful that the arm on the Directional Switch is out of the way when it is slid back into place and be sure that the bracket that activates the Directional Switch is facing the switch in order to send the message to the On/Off Switch to stop the motor when the cycle is completed. The bracket on the front of the compacting unit will force the thin arm on the back of the switch to activate a relay button that is supposed to tell the Rotary switch to shut off the motor and stop the cycle. The front panel and the top panel can then be reinstalled. I checked to see if it solved the problem before putting it back under the countertop. I had to tape the black cutoff switche on the front and on the inside of the container compartment to accomplish this. I then plugged it in and turned the Off/On switch. The unit cycled down and back up but did not shut off and the same noise came from one side at the bottom of the unit. I unplugged the unit and turned it on it's side and removed the bottom plate to inspect the gears and drive chain belt. All the gears and the drive belt were in good condition. So that was not the problem either. That left the Rotary Switch to be the faulty part. I then had to order the Rotary Switch Kit and wait for it to arrive which it did in a short period of time. The old switch was removed by pulling off the handle then using needle nosed pliers to loosen the ring nut that holds the switch in place. This released the old Rotary Switch from the front frame. A flat head screw driver was used to release the wires from the terminals on the switch and place them on the new switch. As per the instructions with the switch kit, the hole for the threaded end of the switch to fit through the hole in the front plate needed to be enlarged. The instructions tell you to use a 9/16 inch drill to carefully enlarge the hole size. Since I did not have that size drill bit, I used a small rat tail file to enlarge the hole. I placed the threaded end of the switch through the hole in the front plate and tried to screw the ring nut back on to the threaded end of the switch. The threads did not pass far enough through the front plate to allow the ring nut to thread and hold the switch in place. I found that there were two plastic ridges on the back side of the front plate that did not allow the threaded end of the switch to fit far enough through the hole to attach the ring nut. I then had to take the front plate off and used a chizel and hammer to carefully chip off the ridges so the theads would fit through the plate and allow installaton of the ring nut. The wires could then be placed on the Rotary Switch, ring nut installed and tightened, the front panel replaced and the top plate reinstalled and the unit tested. This time it worked and the trash compactor was plugged in and shoved back in place under the counter top. Now for the rest of the sto

Pull unit from under counter (Held in place with 2 screws) Use nut driver to remove top and front panel. (I didn't remove the control panel from the front panel which probably made access more difficult) Locate the directional switch near the top of the unit and remove two screws, being careful not to lose a small metal plate into which the screws thread (similar to a Tinneman nut). I moved the wires one at a time from the old switch to the new as I am color blind and have trouble with wire colors. Fit the new switch in place, being sure the switch lever is positioned against the metal tab that operates it. Screw the switch in place and then reassemble the compactor.

Ordered part and received it in two days. Unplugged the compactor from wall outlet. Removed two screws holding control panel in place, marked proper wire location on rear of panel, disconnected push-on terminations from start/run switch. Removed knurled nut holding start/run switch onto the control panel and substituted the new switch. Reassenbled everything in reverse order to disassembly and plugged power cord back into the wall outlet. No further work required.

took longer to pull it out and put it backunder the counter then to pull the panel take the chane gear & drive gear off and put it back together

easy ... got the new bag holder and replaced old one. the impressive part of the process is how easy it was to get the part info from partselect website. could have spun my wheels a lot without that.

very easy to fix. all it took was pulling the compactor out to unplug,take off the removable front nob, unscrew two screws located just below the front panel.using needle nose pliers to remove the actual switch, unplug the wires conected to the switch and put the new one on the same way. It almost took me longer to write this discription than it took to fix!

take 2 screws out on top cover with key switch. remove two screw holding directional switch. remove wires, one at a time, and place on the new switch. put new switch in place with two screws. put front cover on with two screws and test. works like a charm.

All I really needed to do was to take the front facing off and put on the new container, but I took the opportunity to do a complete overhaul and cleaning. It now work like a new compactor.

I removed the unit from under the kitchen counter by first pulling the trash drawer all the way out and lifting it out of the track and setting it out on the floor. I then slowly pulled the compacting unit out and unplugged the cord from the electrical outlet. With the entire unit out in the floor I took a nut driver and removed the screws from the top plate and the screws from both sides at the bottom of the front housing. This allowed access to the directional switch. Two screws on the right side of the switch have to be removed to remove the switch along with two holding plates on the left side of the switch. The switch can then be accesses for removal. Several wires are attached to the switch and should be removed one at a time and installed to the identical identical location on the new switch. The new switch can then be installed by aligning the holes and reinstalling the holding plates. When this is done the front frame and top plate can be replaced with the nut screws. Plug back into the electrical outlet and see if it works. In this case it did exactly what it was doing before I started. So either I did not reinstall the directional switch properly or I am in the one percent rather than the 99 percent that should successfully solve the problem as suggested in the trouble shooting guide. I will now recheck the installation of the directional switch nd then check the bottom of the unit to see if the gears or chain drive are broken .