KUCC151EBL0 KitchenAid Trash Compactor - Instructions

Like others who experienced this problem, I removed compactor from under the counter and laid it on its side. I removed the screws holding the cover plates to the motor and gear/chain box. The larger (4" +/-) plastic drive gear which moves the chain that lowers or raises the compactor ram was broke. Using a socket and ratchet, I turned the shaft the gear was attached to in a counterclockwise direction and moved the compacting ram from the bottom position to the top so I could finally open the door, It takes a lot of turns to move the compacting ram to the top so be patient. I then loosened the bolts, in the base, that holds the motor secure and slid the base toward the broken gear putting slack in the chain. I removed the split ring from the shaft and removed the sprocket which originally is part of the gear but was left on the shaft when the gear broke in three places. I elected to not remove the original washer and spacer and put the new gear with sprocket on the shaft, put the chain on the socket and installed the split ring. Slid the motor base back to original position putting slight tension on chain and a proper clearance between the gear and drive shaft (sheet of paper seperation). Reinstalled the covers, tested and was finished.

I have always used compactor bags made of paper & plastic. I was sent bags made of only plastic. I called and was told that is the only kind available. I am concerned that the plastic bags may not be strong enough.

I quest I will have to try these all plastic bags. I hope they are strong enough and work properly.

changed out the switch and that fixed the problem

Removed 4 screws and the foot release to attach the new guard. Replaced the foot pedal and 4 screws and was done.

First thing I did was put the unit on its side and removed the bottom to access the broken plastic gear that moves the chain that drives the compactor up and down...There I was able to manually move the chain by turning the nut with pliers and moving the piston up (painfully slow) until I could at least use the bin for trash while I waited for the replacement part to arrive. Once I had the part I loosened the four bolts that allowed the drive gear to move a little and slacken the chain - I then put in the new gear - make sure you have the proper spacing and washers - my replacement kit didn't have any washers so I resused the old washers and all seems to be working well!

pulled it out, turned it upside down, and removed the gear, then replaced it, turned it back up and pushed it back it worked.

Bought wrong roller. The drawer roller is different than the stationary rollers. Note the difference.

I followed the you tube video instructions provided by customer care. This involved pulling the unit free from the cabinet, removing several screws that held the housing in place, this gave access to the wheel assembly, then I removed the nuts that held the wheel assembly in place. Fitting the new wheel assemblies was easy as was replacing the housing screws. After reinserting the draw and pushing the unit back into the cabinet it worked like new

This new one from part select I think fit better than the original so all I had to do was install the handles as the depiction on the packaging showed and install it. Less than 1 minute.

remove the container from base lay on floor unscrew 2 screws one on each side and remove foot pedal. I could see that the foot pedal had small bow in the pedal. You can only see this if you removed. I ordered the rollers in the front but did not install as it is not the rollers. Will keep for future if needed. Replace your foot first if hard to open.

Put the parts in and reinstalled it back in it place

Removed the switch knob, the outer nut, and the front plate.
Unplugged the old switch from the 3 wires and plugged them into the new switch and put it back together with the new knob. Probably less than 5 minutes.

remove front panel, remove 4 wires from switch, remove switch from panel. Install switch, attach wires and replace panel.

Upon the receipt of my part it just had to be slipped into place. I had the part I needed within 3 days of ordering.
My had ordered parts for various items in the past and we have always been very satisfied with the care and experteis of this company.

replaced