66513633100 Kenmore Trash Compactor - Instructions

Losses two screws, old part off; install two new screws, new part on. Piece of cake

Removed the screws holding the remaining piece and replaced it with the new part. Hardest part of this whole issue was making sure that I had the correct part on order. Would have liked to have been able to blow up the diagram for easier viewing.

The part has broken several times in several years. Each time it required a service call with a hefty fee. The fourth time I decided to do it myself. I ordered the part. It came faster than a service man would have and I installed it myself with a screwdriver in about three minutes. I will treat myself to lunch out with the girls with the money I saved!!!

The metal actuator had broken off on my trash compactor. It is held by 2 screws. It was easy to remove the 2 screws to replace the actuator. It was somewhat obvious which way it attached to the frame in order for the actuator to hit the white bush button switch located on the lower right of the compactor.

the bearing were the perfect match and instructions helpful. sysem is rolling smoothly

To repair the o.e.m. actuator lever, Whirlpool supplies a redesigned actuator switch. It requires dis-assembly of the front panel which takes time since you must first remove the trash compactor from the cabinetry. Once the front panel is off and you've removed the old switch, installing the new switch requires drilling two holes. Do not use the recommended drill bit -use an oversize bit to match the core diameter of the new screws. The new switch works brilliantly if done right. It just takes time.

Same problem as described previously on this site. Pulled unit out and replaced the gear as described. Thanks for the info - would have been tough with out it.

Many of you with the KitchenAid trash compactor now that there's a faulty Actuator part the continues to break, and most likely have replaced this several times. I was glad to see that KitchenAid finally redesigned a part hoping to solve this problem. Overall, installing the new part went well. The new part does require you to pull out your compactor from the cabinet so you have access. After removing the top and front panels, you'll replace the switch and then install the new pedal that activates the switch, needing to drill a couple holes to secure it. Other than that, it's very simple. Only advice is to read the instructions a couple times to get yourself familiar with what needs to be done...then you'll have a much easier time and feel more confident before you start.

The instructions were pretty straight forward. I did not expect to receive the foot pedal and switch as mine was still ok. However, I find that everything works with less effort than before. I did have to trim the new toe guard as it hit the actuator button when opening and closing the compactor.

I installed the new bracket, however not the new switch that came with the kit as the old switch was fine. The one key which threw me for several hours is, you must replace the switch, located in the compactor. The new switch is normally open when compressed, the old switch is closed when compressed.

Follow the included instructions carefully (read it all through first) and this was a quick and simple fix if you are reasonably handy with a screwdriver and drill. It took me about 45 mins. You have to pull the unit out from under the countertop and then remove a series of small screws in order to get behind the front panel. Putting in the new actuator switch was a little cumbersome simply because there are other wires you have to work around but it's still very straightforward. After you reinstall the front panel, you attach a new foot activated button that presses down on the new actuator switch. You have to drill 2 small holes in the front panel sheet metal to attach this new button but a perfectly sized paper template is provided and it worked great. Last easy step is to replace the rubber door sweep so that the new button can be accessed with your toe. In effect, the compactor is now operated by pressing your toe against the new button on the lower right side below the door. It is a nice improvement over the old method of lifting up on the lever that you normally step on to open the door. Easy to install.

Followed PartsSelect instructions, the Compactor was appoximately $1000. when I purchased it. The kit was $26.14. I will forever be a customer of this company. Thank you, Brian

Thanks to Parts Select and their detailed instructions it turn out great! Replacement Parts fit Great!

After removing the compactor from under the counter, and unplugging it, I did the disassembly. The replacement parts were easy to install. Two holes had to be drilled to mount the switch, but that was not difficult. Overall, the instructions were easy to follow and the parts all fit.

It was an updated revision part kit...and it went so smooth ....recommend that anyone looking to repair appliances utilize PartSelect....I know I will be ...Thank You