SG1000 - Instructions

I used a 1/4 inch socket to remove the agitator.Used a small screw driver to remove clip. Then I lifted the washer off the shaft with a magnet. Pried out the old seal with a screwdriver. This exposes the top of the tub bearing. I applied some 80-90 differential grease to the top of the bearing, pressed in new seal, installed other parts and noise gone. It sounds like a new washer. I'm glad I found you guys.

Removed top screws and the front cover.
Removed lint filter harness/air vent assembly (two screws inside dryer tumbler, 6-7 screws along vent assembly).
Removed front dryer tumbler sealer panel (2 screws on each side).
Scraped off old felt sealer with screwdriver.
Drilled out remnants of old rivets.
Replaced gliders with cork underneath.
Riveted gliders into position.
Used mighty putty to fill the cut metal around the top of the sealer panel (resulting from the dryer tumbler rubbing without proper gliders).
Glued new felt sealer around tumbler sealer panel.
Reassembled the entire unit in reverse order.

There is one good description already posted. I would add:1)If the the nut holding the inner tub doesn't loosen easily just split it with a chisel and don't waste time. 2)Don't order extra washers to remount the outer tub, they come with the bearing! 3)While disassembled I ran the spindle on spin to make sure the brake assemlby wasn't the problem. It ran quietly and smoothly. 4)The inner bearing sleeve was stuck on the spindle and didn't want to free up. I used a rotary tool to cut a groove in the old bearing sleeve then chiseled on the groove edge and it split nicely. It was very brittle. The washer seems to work well now. Next time I see a leak I am going to repair it right away!

first i removed front panel by pulling it from the bottom and then removing the top. then i removed the agitator with a 1/4 nut driver. then i had to open top lid which is hinged and held together by two 1/2 inch bolts. after i opened up the top of the washer i had to remove the white plastic top of the inner tub. in order to remove the inner tub there is a large nut that i had to use a punch and a hammer to break it loose. don't forget this nut is counterclockwise to loosen.hint use a little wd40 due to calcium build up around nut. once the inner tub is removed you should see the rubber bushing. be sure to remove all rust and water calcium build up before installing new bushing. i used a wool pad. put everything back together the way you took it apart and it should fix your leak.

My 11 year old grandson and I did the repair together. He had a blast and I did too. First we removed a bunch of screws that got us no closer to getting the machine apart than when we started. Then I remembered from the last time I had the machine apart that there are two screws just below the door, angled as not to be visable unless you know where to look. Once we removed those the from came off. We removed the wires for the door light and heat sensor, remembering the order of the wires for later reinstallation. Then we undid the bolts holding down the top. Once the top was removed we took off the belt and removed the drum. We used the retainer pliers to remove the retainer ring from the first roller. We removed the roller and also the shaft as this roller was the noise maker and the shaft was not in reusable condition. We installed a new shaft, roller washer, roller, another roller washer and then the retainer ring. We repeated the same process on the other roller, although we did not replace the shaft as it was in good condition. It turned out I did not need to order the shaft washers as the rollers came with washers. Oh well, its not a good job unless you have parts left over when you are done. Once we replaced the rollers we commenced reinstallation. But first we had to google for diagram of the proper belt installation, which we found and that got the drum and belt installed properly. Thankd god for the internet. Once we had the drum installed we put the machine back together in the opposite order we took it apart. An operational test showed we did the job right, no more squeaking. The only injury was my grandson cut his thumb right after I gave him the speech about watching where your hand is going to end up when that bolt breaks free. It broke loose and into the metal bracket went his thumb. Oh well it was a good lesson and it was not a bad cut. All in all a good repair.

Thoroughly cleaned the edges to be sealed with a wire brush and sand paper. shimmed the top piece with 1/4 inch plywood strips. seated the top piece with the seal attached and worked the seal down into place. Positioned the seal clamp, carefully, and tightened the clamp screws. Replacing the seal did the trick, even though the old seal did not look to be in bad shape.

I removed the two screws holding the access panel, and removed the access panel. Then removed the lower air duct. I then checked the burner, The solenoid was not opeing the valve for the gas. I order the coils, in two day I had the coils and installed them. The dryer is working great.

After replaceing several parts including the thermostats the last part I replaced the coils were the defective part. I originally metered out the themostats and they appeared to be okay but since this was my first time I thought I might have been mistaken. It turns out the last part I thought it could be was the part that was defective. I will say that it is very simple to replace any of the parts involved. The hardest part was trying to open the dryer itself. But after having to do it 3 times, I'm now a pro. I also replaced the drum belt and since I had it open I also replaced the belf idler with a newer modified idler rolller.

Putting the belt back on is easy, but it helps to view the video or a picture to understand how the belt goes around it.

Unscrewed 4 screws,pulled off front of machine.Unscrewed 2 screws holding coils on,unplugged coils,installed new coils,plugged in coils,reinstalled 2 screws for hold down brace.Reinstalled front cover,plugged dryer into outlet(remember to unplugged dryer before working on it).started up,instant heat,works great.thanks Partselect for helping me out!!!

A tension sping on the motor broke, smoking the drive belt.
step1...remove front of the washer to access spring, tip washer back & prop on short 2 x 4 board. 5 minutes
step 2... remove one end of pump belt to get new bely up to drive pulley put on belt using fingers only & replaced the end of the pump belt....2 minutes

step 3...put new spring under motor & hook one end in attaching hole on motor, reach through with pliers to grasp spring to pull end to attach spot on base...1 minute

It took longer to open up the washer front & prop it up that it took to repair it. This is a siper easy repair!

Wish there was a video. I am above average handy but this one- I might just pay someone next time...The tape on the threads was a great tip but took a while to understand what they meant by putting tape on the threads. Scraping off the old pads is easy for the front one but the back pad and a half is so hard to reach to really get it cleaned. Bruised and cut knuckles on that one. Then not having the glue for the pads was a surprise and you have to get a good contact type cement that sets in 10-15 minutes or you will be waiting hours to put it back together. It was easy to put the first spring on, then the second and third got harder and harder.

Frist I removed the front cover panel via removing 2 screws. Second I disconnected the door switch wires. Third I removed the 4 screws that hold the drum onto the rollers and guides that allows access to the blower wheel assembly cover. Fourth I remover the blower wheel assembly cover to gain access to the blower wheel. Fifth using the retaining removal tool removed the retaining ring from the shaft then removed the blower wheel using plyers. Then reassembled all of the parts and enjoy a quiet dryer again.

Thank you parts select!!!

First I removed the two screws that held the front panel in place. Then I determined that the belt for the pump had fallen off because the drive belt was worn (and inverted) and a piece was hanging off and causing the pump belt to slip off the motor. I replaced the belt for the pump (Temporarily) to allow the tub to drain.

I replaced both belts with new belts and returned the front panel. The process took 15 minutes due to the necessity of explaining the proper use of tools to a neighbor child and allowing him to assist (required for the completion of one of his Cub Scout requirements).

The ignitor is easy to determine if it is defective. When you start the dryer and the ignitor does not glow , it is bad.
The replacement involves unpluging the dryer, opening the control access door ,the removal of one screw, unplug the bad ignitor, plug in the new ignitor, reinstall the one retaining screw, plug the dryer back in, check for proper opperation of the ignitor, and close the close the control access door.
Very easy

The hardest part was figuring out how to get the front panel off of the washer. Once that was done, the pump came off easy.... 3 screws attached it to the bottom panel and 2 hose had to be disconnected. Putting the new one in was easy.