MFI2570FEB01 Whirlpool Refrigerator - Instructions

Parts delivered quick. 15-20 minute repair time. Just needed to remove a few shelves, then screws to remove damaged parts and replace with new. Very easy repair.

We removed the old switch, unplugged it, plugged the new one in and it was easy to do. But when we tried to put the switch back in we had a very hard time doing it. Eventually got it in, but if it had not been for the difficulty we had getting the new switch to snap in to place, it would have taken under 5 minutes.

I took one screw out, unplugged the light a d the. Installed the new one put the light back in the groove and presto it works great and I saved a lot from having to call and installer and ordering from this company on line alone saved me $90. Awesome!

It was quit simple. I removed the draw and the shelves above the pantry unit. Once everything was removed (2min), I removed the one side pantry bracket ( 2 screw's). Put in the new pantry bracket and screw's and I was done. I'll give it ten minutes total. easy button Thank you

First, I took out the glass tray along with the two slide out compartments that are part of that assembly. Then I used a small socket set to take out the three screws that hold the part in place and along with the part a plastic connector comes out with it that adjusts the temp of the bin area. Line up the holes on the slider and two screws come out that hold the slider to the part. Disconnet the plastic piece in the back that adjusts are flow (press down plastic holders) Reattach the slider, snap the plastic piece on the back and reassemble. Sounds complicated but once you are in there, its self explanatory.

Pop off vent cover remove 2 screws removed cover housing and foam. Removed damper by unclipping tabs on left and right side of control lift up and out. Unplugged power wires reinstalled in reverse order.

Easy fix, it's right in the back of the fridge under a cover that just clips in, a piece of foam, and two screws. The hardest part is getting the clips free without breaking them. After replacement it's silent instead of making a grinding noise regularly.

Very simple--Just remove all drawers, remove old end cap, remove slider from old end cap and put on new one. Screw on new end cap and replace drawers. Took about 10 minutes.

Placed new gaskets on hot patio to smooth them out. Took minion bar off and removed door gaskets. Replaced new gaskets, and minion bar.
Took freezer door off and replaced gasket. I had problems with the first set of door gaskets but customer service replaced them in record time. Service was outstanding. 5 Stars

I broke the glass in the frig and found partselect and ordered the new glass and had it in 2 days. Very fast shipping.

A jar was dropped on the chef's pantry lid and cracked the lid. I unhinged one side of the lid from the pantry drawer by gently pushing outward on one of the hinge pins. The lid slid out easily. I then reversed the process using the new lid and it went in smoothly. Be sure to align the lid so it rests on the shoulder of the pantry drawer. Simple task, no tools, and less than 5 minutes effort. The replacement part was perfect.

The old cover was off and I just slid the replacement part that I got from you'll, it just slid in place and snapped close. Perfect fit. Thanks guys

Remove back cover
Remove drip thing from top to tray in the back
Remove fan motor assembly. This is squirrely. Top bends towards you, bottom pushes in to the unit. Not fun.
CAREFULLY remove copper tube that rests on drip tray
Remove tray - there are clips in the front that get released by screwdriver
Clean up
Replace new tray
Replace copper tube
Play with fan motor assembly till it fits. It doesn't look like it's gonna work until it does. See youtube videos on this.
Replace drip thing from top to tray - I forgot this one the first time.
Replace cover.

This is a simple, but squirrely, repair. Right on the border of easy (because so few tools and steps) and A Bit Difficult because of the patience required.

Watched video. Unplugged refrigerator and popped out switch. In plugged connector and pushed switch in place. Plugged in refrigerator and the light worked

I removed and disassembled the broken frame. I cut a six inch piece of coat hanger and folded in half and crimped together. Then I took pliers and made a hook that I hooked into the metal strip in the back of the refrigerator that holds the upper shelves. After replacing the frame, center rail and glass I bent the wire up under the back of the frame to provide a support. The back of the frame is weak and has no center support.