WRX735SDBM03 Whirlpool Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Glen from PT CHARLOTTE, FL
- Parts Used:
- WPW10350564
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Fridge would not start
Unplug the fridge then wheel the refrigerator out to where you can get to the back - you will probably have to disconnect the ice maker water hose. Using the nut driver remove all the screws from the lower panel on the fridge. You will not have to remove the water hose connection just move the panel around a little. Look on the left side (facing the back of the fridge) you will see the capacitor held onto the compressor with a spring clip. Just pull the clip toward you and that will free the capacitor. Pull up on the capacitor and that will unplug it from the compressor. Be careful not to touch the two poles on the old capacitor. Capacitors store electricity and it could give you a jolt. I used electrical tape to insulate the poles and then threw it away. Plug in the new capacitor- re-hook the clip, reinstall the back panel, plug it in and verify that the fridge is working. Hook your water hose back up and move it back into place and you are done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from West Warwick, RI
- Parts Used:
- W11396033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
broken light switch
followed the instructions provided and that's it!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from Newton Grove, NC
- Parts Used:
- W11396033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Light switch rocker broke, disabling freezer internal light, water dispenser, and ice dispenser
Very simple. Matched female plugs with respective male color coded prong; pushed together then inserted unit in slot of freezer sidewall and rotated into position...job done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brenda from Spokane Valley, WA
- Parts Used:
- EDR4RXD1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Replace water filter
pop open, unscrew quarter turn, screw new one in quarter turn, pop shut. duh
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Keith from DYER, IN
- Parts Used:
- WPW10287601, WPW10212139
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Seal from ice dispenser
The old gasket kept coming off. I pryed off the old plastic insert with a kitchen knife and snapped the new one in. Without the gasket the ice wasn’t being made
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from PRATTVILLE, AL
- Parts Used:
- WPW10714545
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Freezer gasket worn out and slightly torn on top.
I pulled the ils gasket out of track and replaced with the new one. Instructions ncluded state to be very careful with new gasket as the magnets may break. Total time 2 minutes with no tools required.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from BLUFFTON, SC
- Parts Used:
- W10830274
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Bottom gasket closure tab had worn off
Took the gasket out of the box and placed outside I. The sun. For 15 minutes then peeled off old gasket and easily replaced with the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Debbie from Bluffton, SC
- Parts Used:
- EDR4RXD1
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
The filter was clogged.
Replaced filter and the water started to flow like the Nile River and the ice maker came back to life.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Emi from Arlington, VA
- Parts Used:
- W11395888
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
no water when under sink water filter installed
I called the installer of my filter unit and he told me that often, thhe fridge filter is the problem. Like magic it worked
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from ALTO, MI
- Parts Used:
- W10619951
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
leaking water onto floor
replaced the poorly designed "duck bill" drain with this P trap. Very simple repair done by accessing through the back of the refrigerator. The video on this website walked me right through the repair. It did however fail to mention that the ice has to be removed from the inside. I had to remove the drawer face and pull outs. Then the ice maker and back panel are removed. I used a heat gun and screwdriver to chip and melt the ice build up. If one had the luxury of having another refrigerator to move food in to you could just unplug the unit until the ice melts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from RICHTON, MS
- Parts Used:
- W11613295
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Refrigerator would cool for a very short period of time. Then the compressor would shutdown via internal thermal overload or high head pressure. This was caused by the lack of airflow across the condenser coils and compressor.
(1) Slide out appliance and remove power source. (2) Removed lower access cover on rear of refrigerator. (3) Disconnected plug to the condenser fan motor. (4) remove blades by pulling gently forward (5) remove mounting hardware holding the fan motor (3 screws) (6) motor is now free and new motor can be installed
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- kathleen from GREEN VALLEY, AZ
- Parts Used:
- W11396033
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
broken light switch in the freezer
We removed the old switch, unplugged it, plugged the new one in and it was easy to do. But when we tried to put the switch back in we had a very hard time doing it. Eventually got it in, but if it had not been for the difficulty we had getting the new switch to snap in to place, it would have taken under 5 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gloria from Laurinburg, NC
- Parts Used:
- WP67006331
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken latch on water filter cover.
Reviewed replacement instructions video on your website. Just followed the easy instructions to pop out old cover and pop in new cover. I would not have tried to replace it myself had I not seen your video. Super easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jerry from SNELLVILLE, GA
- Parts Used:
- WPW10714545
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
FROST, ICE buildup along and inside the bottom of freezer and door
Removed old gasket by carefully pulling it out of the retaining groove. Installed the new gasket starting the corners first and then seating the upper and lower straight portion gently in the retainer groove. Total time for installation was at most 5 minutes. After a week no ice or frost has been found along the bottom of door or freezer. Note: the new gasket came in a small box for shipping purposes and the new gasket was twisted in a v for this purpose. Upon arrival, I laid it out flat on table overnight so it could cool to room temperature and straighten. I would recomend this procedure for a perfect installation.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frances from TUNNEL HILL, GA
- Parts Used:
- W11338583
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The light was blown
I turned the light bulb into the socket
Was this instruction helpful to you?
Thank you for voting!