WRX735SDBM04 Whirlpool Refrigerator - Instructions

Remove damaged driver glides on both sides, save screws to reuse. Put right glider on right and left glider on left side of drawer and tighten screws with screwdriver.

I just removed the old bin and hooked on the new one.

Open and remove lower cover on filter holder by opening tabs that hold lower cover and remove lower cover.

Firmly hold back of unit and firmly hold and turn filter in counter clockwise to unlock and remove.

Install new filter by holdin back of unit and install new filter by turning in clock wise direction and then replace lower cover.

Followed directions on filter unit

Remove and replace

This problem is caused by a "Duckbill" rubber grommet attached to the bottom drain tube of the freezer. This duckbill opens up during the defrost cycle and allows water to drain down the "water slide" to the evaporator pan. It doesn't take much to gum the Duckbill. Once gummed up the defrost water is trapped. The Defrost Cycle eventually makes the water flow out of the coil area to the bottom of the freezer then eventually to the floor. The repair involves unplugging the unit, removing the bottom back cover with a 1/4 nut driver, pop the power clip out to give you room, reach in and pull the duckbill grommet and the water slide, then installing this replacement drain kit. This is a p trap replacement that actually fixes the root cause of this problem. A tricky part is removing the water slide, you can see the white snap that holds the slide in place. Using a small flat blade from the top releases the snap and the unit is pulled upward rather easily. This replacement drain clip snaps in the same place. If I had to do this again it wouldn't take more than two minutes to replace. Oh, one major thing, you need to manually defrost the unit. I pulled the front door off, it is held with 4 screws ... don't remove them just loosen them and it pops off easily. I pulled the bottom tray out an it gave me room to squirt hot water with a baster into the back freezer area. Eventually everything thawed out. If I had it to do over I would have waited on connecting the tube to the evaporator pan and placed the bottom of the tube into a small sauce pan or something to collect the drain water and easily dump it into the sink. I used a sponge and that took forever. BTW, just to reiterate, use this item and not that Duck Bill for replacement, this actually fixes the root cause of this problem!

Removed icemaker assembly from refrigerator. Short in wiring damaged the wiring connector and icemaker so both had to be replaced. All other parts were reused. Laid out the wiring harness in similar orientation to existing wiring. Removed any covers to expose wiring connectors. Starting at main plug that connects to refrigerator worked backwards and reconnected new wiring at each connection. A few push type wiring fasteners needed to be removed with needle nose pliers for better access. Confirmed all connections were accurate and reinstalled icemaker assembly. Icemaker working properly after wiring repair and tray replacement.

Just plugged it in

Removed the shelf below the cover to allow plenty of room to work spread apart the old cover at the pivot point toward the back installed the new one in reverse order

The installation video for condenser fan motor helped a lot to know how to disconnect the old fan motor and connect the new one. So easy just know how to remove and put back the fan gently, observe carefully where is the center and the connector position; 15 min after everything was done and the unit works well to date.

I noticed the coils very dusty dirty, tried brushing it clean, ended up blowing it clean. I noticed the condenser fan motor was never turning, I had power, so I ordered a new one. I actual received the evaporator motor, so I had to order the correct one. After changing it, and it started blowing right away. But my refrigerator is still warm. I do not know where the evaporator blower motor is located. I cannot make out from the diagram breakdown. HELP

A Screw took off cover unpludge LED lite

The part needed was not available to me so I had to request a service call ... the service tech came out after a week long wait and did not have the switch ... he had to order it which added another 2 week delay to this very simple repair.

followthe instructions in the book that came with the refrigerator

Pried out the old switch and installed the new switch.