5WRS22KNBF00 Whirlpool Refrigerator - Instructions

I removed the items from inside the door and removed the door from the refrigerator at the upper hinge. Removed cam from the door and replaced with the new one. Checked for proper operation and it's quiet as a mouse. I love it.

bulbs were not burnt out. received the new switch in a few days. watch the short video, was good to see how it comes out. used a putty knife to release the defective switch, removed wires put them on the new one and posed the new switch back in. Not bad Part cost $11.00 7 dollars shipping so for 17 bucks it works great. nice to see what is inside the refer!

Eased the putty knife under the edge of the switch housing and pried it off. Pulled two wires off the old terminals and hooked them onto the new one and reinstalled into the refrigerator body.

We looked up the problem online with the model number of the refrigerator. We ordered the part and followed the video installation that was sent with the order and was found online prior to purchasing

1. Unpack carefully so you don't drop it
2. Remove the stickers on the glass
3. Wipe it clean
4. Place on shelf

My two-year-old tried to climb up the fridge for a juice cup and pulled out the drawer, which, of course, broke when it hit the floor. My girlfriend put the new drawer in.

pulled out the old snack pan and slid the new snack pan in.

Removed the door and replaced the lower door cam. Old lower door cam was completly stripped. Insatalled new one and door sealed again! Yay!

They just slid right in

adjusted other shelves up and down as needed, Made necessary room, popped in the new shelf.

The part arrived within two days of ordering. This was the fastest on-line delivery I've ever experienced. Outstanding service!

Unplug Dryer. Remove 2 5/16in hex screws from lower panel and remove panel.Remove 3 5/16in hex screws attaching lint duct. Remove 8 1/4in hex screws attaching blower housing. Remove 2 1/4 hex screws attaching thermostat to blower housing. Using adj. wrench on back of motor shaft nut to hold, loosen fan assy. w/ 7/8in socket. Remove 3 5/16in hex screws holding fan housing to motor mount. Remove 2 5/16in hex screws holding housing and motor mount to base floor. Push belt pulley wheel up enough to loosen belt and take off rear motor pulley. Motor w/mount can be slid out bottom for replacement [wires are layed toward front].Using 6in flat tip screw driver press down to unlock front & back motor bushing holddown clamps. Pinch electrical wire connector ends to pull off old motor. Remove and Install new motor, reversing steps. Belt replacement [suggested w/new motor] requires removal of 2 5/16in screws to lift/remove door w/front panel [disconnect door switch wires upper right rear corner].Remove 4 5/16 screws holding front bulkhead. Once bulkhead is pulled up and off, allow front end of drum to sag and rest IN PLACE [removal not required to slip old belt off and install new belt]. Note belt location point around drum. Slide new belt on. Reinstall bulkhead and panel/door [Don't forget door swich wires]. Adjust belt into position and push spring-held belt pully up to allow looping of new belt around rear motor belt pulley. Complete w/hand turning of drum to ensure belt is aligned and feeding properly. Reinstall lower fan housing/covers/thermostat,etc removed for motor installation.

A very cold and brittle switch in a 17 year old fridge. Used screwdrivers to pry out with some resistance Had to cut the molded plug in half and split wires, because replacement contacts were farther apart than the original. End result, works great.

Figured out You have to pop off the cocer than remove the 1/4 hex head screws only not the philips ones

Removed top cover, then removed top hindge pin plate, then removed the door. Replaced the Lower Door Closing Cam, Reinstalled door and hindge pin plate and cover.

Used a screwdriver to pry loose the old switch, swapped wires to the new switch and pushed it into the opening. Took about 2 minutes.