5WRS22KNBF00 Whirlpool Refrigerator - Instructions

Parts ordered and received within 2days
Opened box, removed old bins and just replaced with new ones,
I am happy when ever I open my refrigerator
Nice product whirlpool!!

Very simply change old part just by hand

install ice maker 2 screws wire harness pluged in done

Simple fix. I watched the video it was great.

DISCLAIMER: Technically, you should start by unplugging the frig and turning off the water supply. Though there is nothing on the my frig door that is either electrical or water related, the frig does keep trying to cooling an open area. For the short while I was doing the work, I just didn't want to bother with those precautions. Had I expected the work to take longer or been working on the FREEZER door I would have most certainly have done it "correctly." But I didn't do the freezer door so, first, remove everything from the refrigerator door storage shelves and the shelves themselves. Then lift off the cap that covers the hinge mounting plate on top of the frig. Remove the screws that holds the mounting plate in place. I used a cordless drill/driver with a 1/4" socket on the end but this could be done with a nut driver or socket wrench as well. Of course, take care not to let the door fall when removing the last screw. Then, lift the door off the bottom post that his holding it in place. The door is not too heavy and one person should not have a problem doing this but if you think it might be too heavy get someone to help with this. On the frig door there are no other connectors to be concerned with. NOTE: This procedure is similar for the freezer door but there are electrical and water line connections that need to be addressed before removing the door. Once the door is off the post, lay it down on a flat work service (I used the kitchen table with some towels spread underneath to prevent scratching either the table or the frig door.) There are two pieces that ought to be replaced. One cam on the door and one at the bottom post. Both are attached with a small screw that is removed easily with your nut driver/socket/drill driver. The bottom cam came offer fairly simply but sliding a thin, flat blade screw driver under it and prying it up and off. Replace this bottom cam with a new one and screw it back down. The door cam was, for me, the more difficult item. Removing the screw was easy enough but years of wear and brittleness led it to break off as I was trying to pry it out. I was able to use a small flat blade screwdriver to cave the old plastic post in all around the insert hole until I could get a good hold and pull it out with needle nose pliers. I was tempted to try to drill the old post out but there is a hex shape to the insert hole I was afraid of ruining. Once I got the old cam out, it was a simple matter to re-insert the new cam. Since both the door and lower cams are held on by screws there is only one way they can go back on. Once the cams are back in place, lift the door back onto the post and reattach the mounting plate to the top of the frig. Take some care that the door is level and parallel to the freezer door before completely tightening the mounting screws and replacing the cap that covers the plate. If you did shut off water and unplug the frig you should turn it back on and plug it back in. And do I really need to tell you to put the shelves and stuff back? :) The door should close on its own when close enough to the frig frame that the cam notches slide into place. If it hadn't been for the door cam being so brittle, this repair would have quite simple. Even at that, digging the old post out really wasn't hard but it did take some unexpected effort. If your refrigerator door is not closing properly, this is something anyone with basic skills can do.

Slid out old shelf and slid in the new shelf

I watched the video, removed the top three screws , took the door off , put the door on the floor and removed the part with a socket.Then I put the new part in after lubricating . I picked the door up put it on the stem below , replaced the three screws and closed the door . The video was a big help was very easy to do and the part was quickly shipped .Thank you for all your help . Patricia

I followed the instructions as laid out in the video associated with this fix. Aside from the fact that the video covers the freezer side door, the fix was the exact same. The video was outstanding and covered exactly how conduct the repair. Incredibly easy to follow and to do and required minimal tools. Wonderfully simple experience that saved a potentially significant amount of money to hire an appliance repair person.

Ice maker fit perfectly over 2 top screws. I tightened them and put the one on the bottom. I was done in less than 10minutes. Everything fit perfectly as expected. Couldn't have been eaiser. Parts Select is my go to online store.

Installed ice machine components using kit and included instructions. Easy! Ran a copper line from under sink valve to back of refrigerator under the floor. Drilled two holes to run copper line. Plumber turned water off and replaced single valve with a double valve (one line to faucet and the other for the copper line). Installed shut off valve and filter at the other end of copper line. Then stainless hose to refrigerator. Everything went smooth. Double check the factory installed plastic line from the electric valve to the inlet for your freezer. Mine was barely inserted and leaked. I pushed it in all the way and it is fine now... Ice maker works really well! Wish I had done this sooner!

slid the new drawer in place

Saw online info video explaining the possible cause and how to fix it. Ordered upper closing cam. Removed top hinge cover and hinge, removed door set it on a table. Removed old cam installed new cam tightened the retaining bolt put the door back on aligned it with freezer door and bolted it down snug. No more noise and it took less the half and hour.

I just popped out the old switch with a flat head screwdriver. Removed the connections and then installed new switch by reversing steps. Popped in back in and the light went on.

We’d had the refrigerator repaired a year ago by the service department of our local appliance store. Turns out the service tech somehow used the wrong screw when replacing the door cam, causing it to rub on the cams and causing premature wear. After watching the provided repair video, it took about 10 minutes to remove the door, replace the cams and reinstall the door. Saved well over $100 and had the job done right this time.

Pried out old part with screwdriver. Unplugged. When new part came, just plugged it in and pushed the part into place.