3XARG496WP00 Whirlpool Refrigerator - Instructions

Removed the cover plate on top. Used a wrench and the nut driver to remove the three screws & the screw holding the grounding wire. Pulled apart the plastic coupling for the wiring to light the freezer. Then with the aid of a friend - lifted the door (with food removed from door shelves) off the hinge. This freezer had a water line which we didin't know how to disconnect so we were careful to move the door slightly away from the broken hinge, set it on a stool with one person holding the door steady while the other person installed the new hinge piece. Definitely takes two people (as suggested in the directions) to both lift and guide the door into place. Once it was in place - I reinserted the screws up top and tightened them. Then had to untighten them to get the door to line up as it should vertically - so I would suggest just lighten tighen the upper screws until the door is aligned and swinging smoothly. Then reattached ground wire and plastic coupling. Works great.

Followed the video instructions.

Remove one 5/16 screw from top hinge cover plate. Trace outline of hinge on top of refrigerator with sharpie, so you will know where to put hinge back. Remove 3 5/16 screws from hinge. Lift door up out of bottom hinge, place on table to be able to work on. Remove one 5/16 screw and upper cam piece from bottom of door and replace with new upper cam piece. Remove one 5/16 screw and lower cam piece from bottom hinge on refrigerator. Replace with new lower cam piece and one screw Set door back in place and reattach top hinge with 3 screws adjust refrigerator door as needed for a nice even gap between freezer and refrigerator doors. Tighten screws down and put hinge cover back on with one screw.

remove door, replace cam, replace door

Placed tray on lower part of refrigerator.

Slid the old drawer out and slid the new drawer in. Less then a minute!

I pulled off the panel covering the part in the freezer cut and stripped the wires. Used crimper and connectors put the new part on put the wires band panel back on and plugged the refrigerator back in. Everything works just fine now.

Piece of cake. It took me longer to remove the food from the freezer, remove shelves and back panel than to do the repair. I heard the fan making some noises so I replaced both the fan and defrost thermostat. I used the instructions submitted by a another customer. My 20+ year old fridge is like new now.

I follow the video From The Tech Guy ( Gentleman ). Thank you... Best Regards .Fco

watched your instructions

I did some tests and determined that the tub-to-pump drain hose had a leak in it.I then looked on the web to find disassembly instructions. I have a stacked washer dryer combination in a very confined space. The repair involved disconnecting both the washer and dryer from the water, gas, electric and venting systems first, then unstacking the dryer from the washer (not so easy, it required a helper). The machine was then pulled out so I could get at the parts necessary to remove the outside components and sheet metal. Then, I disassembled the top, front and access panel in the back. The disassembly went very well. I got access to the drain hose assembly and removed it fairly easily. I ordered a replacement drain hose assembly and found that installing the large port of the assembly was very difficult. (The two other ports were easy.) After thinking about it, I tilted the machine back a bit so I could try it from the bottom. That worked fine.I then reassembled and tested the machine. No leaks. Good luck with yours!

Following the instructions on the site I removed the upper hinge cover and hinge(after removing the shelves from the door). I replaced both cams on the bottom hinge, reinstalled the door and the problem was solved. A couple of hints that may speed up the process: 1. On installing the door cam, I didn't get the holes in the door and cam aligned well due to a bit of interference from the metal tab on the door, so I temporarily inserted the upper hinge pivot in the bottom hole and retightened the cam. 2. I decide to re-align the freezer door . After this, the ice and water dispensers didn't work. Turns out the internal freezer light switch which also acts as a cutoff switch for the door dispensers wasn't being activated. Easy to adjust once the cause was discovered.

Followed instructions that were online when ordering part. Put a adjustable wrench on the square end of the plastic support and twisted upward. Support bracket came off easily. Inserted new part and twisted downward on the square end of the support and it locked in place. Surprised it was so simple.

Just followed the video supplied with shipment. 5 minutes, even for a mechanically-challenged person.

Simple read about three of the other peoples repairs,did the same and (PIECE OF CAKE)
Only problem ordered the cam kit with shipping over # 18.oo and only needed two pieces to do the job. Should have ordered just the two cams and saved a lot of dough.
But done and over with a happy camper (WIFE)