6ED20TKXDW00 Whirlpool Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Wm. from Naples, FL
- Parts Used:
- WP2198202
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Unit would freeze then defrost but not go back into freezing again untill I moved the thermostat
Turn off power .Remove the control knobs and pry off the front panel ,it just snaps on,Take out two screws holding the control panel Take out the two screws holding the control to the base of the panel to get at the two screws holding the control to the bracket. Ther are screws holding the covers over the thermostat tube. Then pull out the tubbe and remove the plastic cover on the old control and place it on the new control tube. Then route the new tube into the snaps be careful to not make ant sharp bends in tubing.When that is done fasten the control to the bracket and fasten the bracket to the panel.Replace covers over tube to hide it and keep from damaging it when putting things in fridge.. Mount the conrol bracket back to the fridge and replace snap on cover. Plug in electric.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patricia A. from Toccoa, GA
- Parts Used:
- WP2198202
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Our refrigerator failed to cool in stages, finally quitting to cool or run.
First, after re-reading your descriptions here on your site ( it took clues from each of them) I unplugged the refrigerator and began on the only day my husband was out of town. The two selector knobs came off easily fingers only. The plate came off with only a slight prying with a screwdriver (it is intended to snap off this way). Loosening the screws and removing them in order to remember which order they returned proved to be a challenge. After disassembly, pulling the thermostat out of the tubing and replacing it with the new one without bending it was hard to do also. The refrigerator runs like new, and may run another eleven years! Thanks!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- edgar from PAWTUCKET, RI
- Parts Used:
- WPW10225581
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
refrigerator not freeze
i didn't repair replace capacitor, bi metal defrost thermostat and still not freeze also replace light door switch any suggestion thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Miami, FL
- Parts Used:
- WP2188664
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
cracked meat pan
Very simply change old part just by hand
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ouida from LORMAN, MS
- Parts Used:
- W10508993
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Tray missing
Simple fix. I watched the video it was great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- wendy from palm coast, FL
- Parts Used:
- W11581579
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Shelves in freezer falling off
Went online with the model number, the part was very easy to find, diagrams helped me to have confidence in the choice. Parts came in two days, tore them open and used a screw driver to replace the broken shelf brackets, replaced shelves, I am a happy camper!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jenice from Angleton, TX
- Parts Used:
- 4388538
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench (Adjustable)
shelf had no support
inserted stud and twisted
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chris M. from Madison, WI
- Parts Used:
- 4388286
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old end caps tabs broke off.
I removed old end caps from refrigerator door shelves and removed existing shelve brackets from end caps. Then I put new end caps on existing brackets and snapped them into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bart from Salt Lake City, UT
- Parts Used:
- 4318165
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Refrigerator door wouldn't close on it's own anymore
All I had to do was remove the screws at the top of the refrigerator door that hold the top hinge and once that was done I lifted up on the door and it came off. I then flipped the door upside down and was able to replace the door cam on the door and the other cam on the bottom hinge of the refrigerator. Once replaced, I put the door back on and put the screws back in on the top hinge of the refrigerator door. Works great now!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ramona from Fort White, FL
- Parts Used:
- 4388286
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
shelf end broken
snap the part in and replace the shelf
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MATTHEW from STOCKTON, CA
- Parts Used:
- 4387478
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The Light Socket Burned Out.
I pulled the socket out and unplugged the wires. I replaced the light socket by plugging in the wires and snapping the light socket into place. A very simple fix.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Hamid from Owasso, OK
- Parts Used:
- W11581579
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
My wife broke the shelf support
The new shelf support part fit perfectly. I needed no tools just slid it on the existing bracket. Super easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Cary, IL
- Parts Used:
- W11581579
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
A couple supports broke
I simply slid off the broken supports, and slid the new ones on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Max from Jonesboro, AR
- Parts Used:
- 4386774
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Broken wheel on leveling roller
I removed one bolt and took out the old roller after first blocking up the fridge. Then I was puzzled for a moment because the hole in the new assembly was not tapped. But then I saw that the old bolt was a self tapping bolt. I used it to tap the hole then removed it and installed the new assembly. No sweat job.
Was this instruction helpful to you?
Thank you for voting!
End cap clips that attach to refridgerator frame broke off from wear and tearkid use
I uncliped the old broken peices and snapped the new ones in its place. easy as 1 2 3.
Was this instruction helpful to you?
Thank you for voting!