3XKGN705000 Whirlpool Refrigerator - Instructions

After discovering that the water noise was coming from the rear of the refridgerator upon pulling it foward I discivered the connection line had broken. So i got a phillips screw driver and removed the the two mounting screws and saw it was one piece. I easliy found the part on PartSelect website and once I got I merely swaped them out and it works good as new!

Pulled out the ice bin and dumpted ice in the sink. Use 1/4 inch nut driver to take out all 1/2 inch screws. Be careful to watch how door spring and holder goes. Pull assembly apart and remove alger. Plastic nut on end of alger has reverse threads, remove it and then remove broken alger drum. Replace with new drum and reassemble in reverse order.

Replacing the parts was easy. I am 62 years old and have been repairing all my own appliances for yerars. I have found more problems in recieving the corect parts in a timley mater more difficult than fixing the problem. I am impressed with the promedness of your delivery, and in rtecieving the corect parts. Thank you much!!!!!!!!!!! Bill

Very easy to order from parts select. Took seconds to replace.

1. Pull out drawer. 2. Remove screws to release the auger. 3. Unscrew the end of the auger. 4. Pull parts off. 5. Replace drum. 6. Replace parts in the correct order. 7. Twist end of auger back on. 8. Replace unit onto drawer and install mounting screws. 9. Place drawer in freezer. 10. Test ice dispenser. 11. Watch kitten run to refrigerator and beg for ice cube. 12. See smiles on family members faces.

This was very easy to install. Part Select had very fast shipping and reasonable prices. I love this website they have everything you need for your appliance. My ice door was very easy to install. I popped it into the grooves on the ice maker. It took about 30 seconds. THANKS PART SELECT YOU ARE GREAT!!!!!! :-)

I took out the ice bin and in the back where the auger meets the ice bin I had to replace the small plastic piece to hold the auger in place when using the automatic ice maker. It was an easy fix.

Fairly straight forward remove and replace. Tight limitations made it a little difficult but universal joint for socket set allow the best access to the screw that held the lever in place. Replacing the spigot onto the water line was a concern. The fit was so tight you must take care not to damage the plastic line.

I pulled off the panel covering the part in the freezer cut and stripped the wires. Used crimper and connectors put the new part on put the wires band panel back on and plugged the refrigerator back in. Everything works just fine now.

I was able to transfer my old ice maker from my old Roper Refrigerator/Freezer into my new Whirlpool Sidekick Freezer. Everything transferred directly except for the water fill tube. I ordered one on line and simply cut it to the right length, removed the cover plate inside the freezer compartment and the little sticker from the outside. Inserted tube and fastened in place with two screws (not provided but was able to use the screws that were in the holes inside the freezer before the ice maker went in. Works great. By not buying the ice maker with the freezer I saved a hundred bucks or so.

Unplug refrigerator. 1. Using a thin screwdriver, slowly and carefully pry the front panel off that is around the ice and water dispensers starting at the bottom. Once the bottom side has been popped off, carefully lift up on the panel until the top tabs pop loose. 2. Remove the next panel (5 screws) which holds the light and two switches with a screwdriver or nut driver. I then taped it over to the side onto the freezer handle to keep it out of the way. I preferred not to unplug anything. 3. Remove the door mechanism with a nut driver. The same screw holds the water spout and door mechanism together. 4. Reverse the steps and you're done! I now have a silent ice door.

I followed the video exactly, pausing it as I went along. So unbelievably easy! And I’m 78 year old great -grandma! Thank you

Exactly as the demo instructed. It was very detail friendly and was very easy to follow.

Freezer worked great, refrigerator stopped getting cold and lots of ice formed around the condenser on the bottom of the refrigerator.
First I had a serious ice issue, ice build up around the bottom of the refrigerator and all through the cold air vents, condenser and cooling fan. I unplugged of the fridg and let defrost over night. I also took all the cold air vents out and cleaned them.
Then I followed the switch install video very simple switch install. Now the Refrigerator works Great nice and cold.

the process was pretty straight forward though the part came without instructions. We were able to replace the part improperly with ease. however, we were not able to get the pieces aligned properly for a long time. We ended up taking the door off many times to try to realign the pieces. After many hours I finally unscrewed the bottom cam while the door was in place. The piece popped into place and all was fixed. Had the part come with directions telling us to do this we would have replaced the cam within 15 minutes!