ED2JHAXTB01 Whirlpool Refrigerator - Instructions

Removing the panels inside the freezer section was the most difficult ,because it is narrow,hard to fit your body inside compartment, in order to cut wires and to splice Bi-metal Defrost Thermostat wires (2 ) Watch the videos on the web site so you know where to start. First time I ever "repaired " a large appliance, saved me over $ 600.00 (that's what the people I bought the Refrigerator from wanted to charge me.) My parts cost 65.00 !!!!! My younger brother turned me onto the web site... , I'll be returning to the site and telling my friends about it. It's a total "rip off" what service organizations charge the general public these days from Car Dealer ships to the stores we purchase our appliances from. !!! Glad I still have my health and faculties to repair the essentials we have around our homes. !!!!

New part slipped right into the studs and fit perfectly

Removed upper hinge cover and hinge, lifted door from lower hinge socket, removed lower cam from 'frig hinge, and replaced with new. I had a helper hold the 'frig door while I removed old upper cam, and replaced with new. Piece of cake and works like new! This must be a design problem..

Approximately:

1. Unplugged refrigerator.
2. Emptied Freezer.
3. Removed Ice Maker.
4. Waited a few hours for ice to melt around back panel & nuts.
5. Removed back panel and the cover over fan and fan motor.
6. Waited many more hours for ice to thaw over fins, wiring, etc.
7. Easily replaced the bi-mental defrost thermostat.
8. Replaced panel, fan cover, ice maker.
9. Plugged in refrigerator and waited a bit.

This worked! Yahoo.

p.s. I am a 65+ year old mechanically minded woman. :-)

We took out the old filter and put in the new one. Ran out a few gallons of water then it was ready to use.

removed the drive shaft (6 sided) with seals and replaced it. They last for about 5 years and have to be rotated (flipped over) to continue to use. The shaft metal is a little softer than the drive socket on the motor which, over time will cause the six-sided (12 inch) shaft to round the edges due to torque and pressure on the mixing shaft inside the ice bucket the the door of the freezer.

Remove the unit cover by unsnapping from the bottom. Remove the face plate on the switches. The ice door simply snaps off the closing mechanism. The problem I have is that the original door included a heat trace element (keeps the back of the door warm to limit condensation). The new part was simply a new seal. I clipped the leads to the het trace (turn off the fridge before you do that) and put in the new door. When the heat ids on in the house there is no problem with condensation but on warmer days its pretty bad. I cannot find a replacement part with the heating element and have contacted Whirpool. THey haven't responded as of yet.

I just slid the new pan in , partselect has the correct part all the time , I repalced my ice maker once and it took 15 min no problem

plastic warped in ,spaced out and, the socket snapped back in place.

Remove old tray, replace with new tray.

Simple & easy.

Best part is I ordered on Monday & received on Tuesday!

Ordered the parts from Parts Select and had them within two days (lightning fast shipment--and with just standard shipping). Disconnected the power to refrigerator, removed three screws from each cover panel, pulled the panels loose from the freezer wall, disconnected the wiring harness on each, removed the screws holding the two boards, replaced the boards with the new ones, attached boards to cover panel with screw, reconnected wiring harnesses, replaced the three screws on each side, restored power, and made ice! Whole job took about 15 minutes.

First I removed all contents from inside refrigerator door.Then I removed (1) 10mil screw,which holds cover for top hinge.Next I removed the (3) hinge screws,and lifted door off of bottom hinge.Pulled off plastic closure cam from bottom metal hinge post.I cleaned metal post ,applied a small amount of vaseline to post, slid on new plastic cam,installed door, replaced screws.Very easy,10 to 15 min tops.

I didn't have to buy a new Ice door kit. The part on the Refrig. door I needed I found out was unavailable. The door parts (Ice door parts and the asembly for the water unit) screws into that part. I found out that I would have to replace the whole refrig. door which was $900.00. I took every apart got me some pvc glue used it on the door and bought the original screw online with some other assorted parts,Door switch, etc. and was able to repair in about an hour. Some of the parts are very fraigle so you have to be very careful or you will be buying some new replacement parts.The new nickel and dime parts are expensive. My Icemaker was leaking where the Ice was clumping together in the bin, and when I checked the unit was $125.00. I found a new one and replaced it for about half that price. I am now very happy! (a least until the next project.)

Unscrew the three phillips screws holding the flipper and electric eye unit, pull it out a bit to unplug the connector. Take the assembly over to a flat surface, and use pliers and or crew driver to pry/pull off the press-on retainer on the hinge pin. Pull out hinge pin, remove the broken flipper. Put new flipper in place making sure spring is behind the flipper (holding it open). Reinsert hinge pin, and then reuse the press-on retainer to hold in in place. Then take the repaired assembly back to the freezer, re-plug the plug, and then reinstall the unit using the 3 phillips screws. Easy Peasy.

Using a 1/4" nut driver and a philips screwdriver I removed all the screws in the shelf brackets and coil cover and removed coil cover. Removed fan blade and then faulty motor (held in with clips) Installed new motor-two wires (power) and ground (green) pushed fan blade back on and tested, then reinstalled all panels and shelf brackets.