ED20SKXXW00 Whirlpool Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Steve from Fallbrook, CA
- Parts Used:
- WP2198202
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
Frig did not turn off (stay running all the time) but originally did not run until I wiggled the temp nob
Just followed the Video I found on your site. Seems to work good now, took awhile to get temp setting correct (had to set it a little colder about half way between the "b" and "c" setting).
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- stefan from BLOOMINGBURG, NY
- Parts Used:
- WP2198202
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
Thermostat stopped working. Only cooled at highest setting.
Repair video was excellent but thermostat unit was slightly different then original. Fortunately guessed right regarding connections. Also very difficult to place the insulating plastic on wiring. Not very smooth. Also removing panel was different then in video. Needed to remove the panel to reveal two screws underneath that need to be removed along with the ones at the ceiling.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Milton from NEW YORK, NY
- Parts Used:
- WP2198202
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
needed termastat
your video made it very easy...Thank You
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from CARROLLTON, GA
- Parts Used:
- WP2198202
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Freezer would go from zero to 55 degrees. Ruined all my food.
Followed instructions in video.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- pat from sayner, WI
- Parts Used:
- WP2198202
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
fridge was too hot or too cold
replaced tsat
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dawn from RED WING, MN
- Parts Used:
- 4388538
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
Broken support on lower drawer shelf.
Important: Do not twist broken stud to remove if possible, just pull with the pliers straight out. I twisted it and made the hole larger. Even so, I just used Gorilla Epoxy glue to secure the new one (follow directions on the package) and it's fixed. It's been a couple days and still looks secure. Thanks for the quick delivery.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Fairfield Glade, TN
- Parts Used:
- W10822278
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Freezer Cold - Refrigerator Warm
After searching online to diagnose the issue with my refrigerator being warm and the freezer being cold and not shutting off to defrost I decided to get the defrost timer kit. The kit arrived within 2 day. With the directions included, after unplugging the appliance for safety, I installed it relatively quickly with only a screwdriver . I then plugged it back in and it immediately went to defrost. I thought, wow I have it fixed. Well unbeknownst to me it still didn't cool in the fridge area. After doing more internet research I found a suggestion to unplug the fridge for 24 hours to unthaw ice that may be lodged between the freezer and fridge that is blocking the distribution of cold air into the fridge. After doing this, it now works like a charm.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from Jay, ME
- Parts Used:
- 4387535
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
compressor clicks on for about 5 seconds and then shuts off, evaporator fan is running but no cooling in the fridge.
Disconnect power. Remove back panel on the refrigerator. Relay and overload is a modular unit attached to the compressor. Disconnect module from compressor, install new unit. While you're in there clean the condenser coils with a vacuum and clean the fan and condensate pan. Reassemble, and you're chillin. Total time approx. 15 min.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- yolanda from Clayton, NC
- Parts Used:
- WP1110713
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Bar End caps broke
The replacements fit perfect and there was no need for tools.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Hamid from Owasso, OK
- Parts Used:
- W11581579
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
My wife broke the shelf support
The new shelf support part fit perfectly. I needed no tools just slid it on the existing bracket. Super easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Cary, IL
- Parts Used:
- W11581579
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
A couple supports broke
I simply slid off the broken supports, and slid the new ones on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Max from Jonesboro, AR
- Parts Used:
- 4386774
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Broken wheel on leveling roller
I removed one bolt and took out the old roller after first blocking up the fridge. Then I was puzzled for a moment because the hole in the new assembly was not tapped. But then I saw that the old bolt was a self tapping bolt. I used it to tap the hole then removed it and installed the new assembly. No sweat job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janice from Waunakee, WI
- Parts Used:
- 4388538
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
broken shelf peg
followed video instructions
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from ALBUQUERQUE, NM
- Parts Used:
- WPW10329686
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Broken door stop.
Replaced very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lee from AMARILLO, TX
- Parts Used:
- WP2196100
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
end cAPS BROKEN from shelf
attach caps to each end of shelf and fixed to door
Was this instruction helpful to you?
Thank you for voting!