GZ25FSRXYY6 Whirlpool Refrigerator - Instructions

unscrewed old filter, screwed in new....good to go!

Turn ice maker off
Remove ice tray
Remove side panel cover
Unplug ice machine
Slide ice machine out remove bottom section
Install new ice machine

Very good instruction videos on you tube.

following the video instructions on the website, I was able to remove the bad reservoir in line and install the new reservoir and line ordered through parts select. thank you for your delivery service, and instructions.

Replaced motor it was not issue. Now I am stuck with a $300 motor I cannot return. When I say will not dispense ice everyone thinks it does not make ice. Auger does not turn to push ice out the door. Reason I thought it was auger motor when you push lever on door the auger turns about one eight of a turn. So, it would seem it is getting signal and power. Cannot find any articles on this specific issue. If anyone has a suggestion, please share.

Took the old one off put the new part on. Took 1/2 hour

Checked Video online. Had to remove the 2 snap on track/gear covers. Pry out the gear with screwdriver and the gear bearing unit. Align the flat side of the bearing unit and snap in. Position the cut teeth on the gear to match original and snap into the bearing. Insert the connecting rod into the long shaft gear and then push back into the short shaft gear. The video said to remove the drawer front but I did not and don't see that it necessary.

Removed the shelf below the cover to allow plenty of room to work spread apart the old cover at the pivot point toward the back installed the new one in reverse order

Everything went as planned except the cold temperature (freezer door switch located inside freezer) made deflection of the switch locking tab difficult to remove. Letting the switch warm up was not an option.

Replaced the solenoid that feeds the icemaker. Easy fix remove the trays on the right and remove rear panels on the inside of the refrigerator. Pop the inlet solenoid replace it. Be sure to shut power and water OFF.

Watched you tube video,.....followed,....went very well.....picked the right wiring harness,.....no problems.......making ice in 1 hour

replaced condensation tube with upgrade thawed freezer compartment so outlet hole was free of ice. that means pulling back compartment open to verify the hole is indeed free of ice. the ice maker on the other hand was freezing up solid, replaced solenoid config. as recommended by the tech. still same scenario. turned freezer temp up as far as it would go past recommended temp, which is 4 above zero F. still same results water cup that feeds the tray freezes solid then water runs all over a freezes until you cant get the tray out to work on it. moral to that story it didn't work.

Followed the instructions in the video provided via email from Partselect
However, the part received was the opposite design of the part removed.
It appeared this could be left hand right hand choice of part. Moreover, the button on the switch that turns the light off/on when door is open/closed was not functional due to the part being the opposite of the part I was replacing. I tested the switch I was replacing and it appears this is not the problem. I think the light socket is the problem. I am 69 year old female and capable of doing small repairs, but limited knowledge of electrical so having to troubleshoot by trial and error. Thank you.

I followed the video. If there is an exact opposite of handyman or mechanic, it would fit me. I don't fix things well and I have very little patience for fixing things.
I fixed this easy by following the video. The first side took about 30 minutes because I was super cautious. The second side took less than 5
minutes because it was really easy.

Checked a video on YouTube and found questions and answers to this concern.. All lead to the compressor capacitor. Entered part # on your Website. Capacitor come right up and also suggested a Start Device. I ordered both parts as I was not sure if these parts would fix my problem.
R/R rear panel, found Capacitor and replaced it... Compressor came on and refrigerator operated correctly after defrosting Evaporator coils..

Unsnapped and pulled off small cover exsposing two phillips head screws. I removed larger cover and styrofoam insert fully exsposing the damper unit. i unplugged same and with a 1/2 inch wood chisel was able to release the "snaps" holding the old unit in place. Simply reverse procedure to install new unit.