GZ25FSRXYY7 Whirlpool Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- John from Ketchikan, AK
- Parts Used:
- EDR4RXD1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Low Water Pressure
Followed directions on filter unit
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel F from CALEDONIA, MN
- Parts Used:
- W11613295
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Freezer and refridgerator just stopped working.
The Condenser Fan Motor was already removed due to searching for the problem. The new fan motor looked different from the original but I felt very comfortable that Part Select had sent me the new part showing original part number changing numbers over the years. Simply placed the fan blades onto the new motor lined up 2 of the holes placed screws and tightened then plugged the wire ribbon into the Condensor Fan Motor, plugged in the Refridgerator and it worked beautifully.
The instruction video on the Part Select Web Site made it so incredibly easy to install. Installation took under 3 minutes!
The instruction video on the Part Select Web Site made it so incredibly easy to install. Installation took under 3 minutes!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from PORT JERVIS, NY
- Parts Used:
- W11396033
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
No problems
Just plugged it in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- lawrence from TRAVERSE CITY, MI
- Parts Used:
- WPW10196393
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Noisy, running constantly motor in damper unit.
Unsnapped and pulled off small cover exsposing two phillips head screws. I removed larger cover and styrofoam insert fully exsposing the damper unit. i unplugged same and with a 1/2 inch wood chisel was able to release the "snaps" holding the old unit in place. Simply reverse procedure to install new unit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from KELLOGG, IA
- Parts Used:
- WPW10349187, W10619951
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
condensation line backing up freezing in freezer compartment. ice maker freezing up into inlet tube.
replaced condensation tube with upgrade thawed freezer compartment so outlet hole was free of ice. that means pulling back compartment open to verify the hole is indeed free of ice. the ice maker on the other hand was freezing up solid, replaced solenoid config. as recommended by the tech. still same scenario. turned freezer temp up as far as it would go past recommended temp, which is 4 above zero F. still same results water cup that feeds the tray freezes solid then water runs all over a freezes until you cant get the tray out to work on it. moral to that story it didn't work.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lenny from Boca Raton, FL
- Parts Used:
- WPW10350564
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Freezer Cold at 2 Degrees, Refrigerator Warm at 48 Degrees
Checked a video on YouTube and found questions and answers to this concern.. All lead to the compressor capacitor. Entered part # on your Website. Capacitor come right up and also suggested a Start Device. I ordered both parts as I was not sure if these parts would fix my problem.
R/R rear panel, found Capacitor and replaced it... Compressor came on and refrigerator operated correctly after defrosting Evaporator coils..
R/R rear panel, found Capacitor and replaced it... Compressor came on and refrigerator operated correctly after defrosting Evaporator coils..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christine from SAN DIMAS, CA
- Parts Used:
- WPW10714545
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The freezer door was not staying fully closed.
I watched a YouTube video real quick to see what I had to do and got to the job at hand. I removed the old gasket by pulling it out of the track and bring it around the front of the drawer. I wiped down the entire area where the new one would go and started inserting it into the groove, making sure it went in completely in on the bottom. I was done in less than 15 minutes. Super easy! This fixed the issue and the freezer door closes fully.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Raymond from GLOUCESTER PT, VA
- Parts Used:
- W11489993
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Replaced left side guide on the freezer basket drawer.
Removed Phillips head screw on the front cover of both guides. Pull the drawer forward until it stops. Snap up the cover on each geared wheel to allow the basket to lift enough to continue removing the basket.
Swing the front of the guide rail towards the back which allows for the rear tab to come out of its hole.
Put new guide back in following reverse order.
Done!!
Swing the front of the guide rail towards the back which allows for the rear tab to come out of its hole.
Put new guide back in following reverse order.
Done!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marybeth from VACAVILLE, CA
- Parts Used:
- W11395888
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Lost cap for filter
Bought new cap.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robin from HOLLYWOOD, FL
- Parts Used:
- WPW10212139
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
One of the door bins was cracked.
I just removed the old bin and hooked on the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Denise from TROPHY CLUB, TX
- Parts Used:
- WPW10194032, WPW10194031
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Drawer glide was broken on each side so drawer was not in properly
Remove damaged driver glides on both sides, save screws to reuse. Put right glider on right and left glider on left side of drawer and tighten screws with screwdriver.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lee from TAYLOR, AZ
- Parts Used:
- W11173556
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Broken
Remove and replace
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janeth from PHOENIX, AZ
- Parts Used:
- WPW10296571
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Just the Right Size
Replacing a glass shelf
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carlton from CHICAGO, IL
- Parts Used:
- W11396033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Light out.
Popped out the old switch and replaced it with the one dying
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth E from AUGUSTA, KS
- Parts Used:
- W10882923
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Icemaker quit
Watched you tube video,.....followed,....went very well.....picked the right wiring harness,.....no problems.......making ice in 1 hour
Was this instruction helpful to you?
Thank you for voting!