GI6FARXXB02 Whirlpool Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Theo from Layton, UT
- Parts Used:
- WPW10498990
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set, Wrench (Adjustable)
Water inlet valve not working
Followed instructions for testing and replacement on You Tube video.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeffery from RUSTON, LA
- Parts Used:
- W10502642
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Wrench set
Had to replace the water reservoir on my refrigerator
The replacement part provided was not an exact replacement. The part did not include a water reservoir. Instead, it had a 25 ft long water line that ran from the water filter to the water connection behind the fridge. The long water line was difficult to deal with, did not fit easily into the space provided for the water reservoir, and is coiled up behind my fridge. The part did work, but I'm unhappy with not having the resevoir.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Adam from Los Angeles, CA
- Parts Used:
- WPW10326469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken guide rail
This took 30 seconds. Lift out shelf glass, remove broken pieces, snap new part into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cuong from Camarillo, CA
- Parts Used:
- 8201515
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Ice maker just stpooed making ice
The troubleshooting time takes about 20 to 30 minutes. After checking out the solenoid (valve water), the water line, and the electronic board (emitter/receiver) are working fine. The only thing left is the ice module. I called Partselect and talked to a sale rep to make sure I get the right part, and the lady was so helpful by sendind the picture of the part so I can review before ordering it. I received the part in 3 days ( normal shipping) and did the folowings:
1) Unplugged the power cord from refrigerator.
2) Removed the ice module by removed a 1/4" screw from under the right side of the icemaker that retains the icemaker and a “U” plastic clamp and then pull out the whole unit it from the track.
3) Unplugged the cable connected to the ice maker.
4) Using the phillips screw driver to remove the 3 screws. Carefully pulled out the ice module and installed the new ice module.
5) Put the ice maker back to the freezer, plug the cable back to the ice maker and put the clamp and tighten the nut.
6) Plugged the power cable back to the wall.
The first ice I got in an hour and a full bucket of ice in less than 24 hours. I spent less than $80 for the whole thing. Thank you so much Partselect for the great service and the stories posted, it really helped me to get it done.
1) Unplugged the power cord from refrigerator.
2) Removed the ice module by removed a 1/4" screw from under the right side of the icemaker that retains the icemaker and a “U” plastic clamp and then pull out the whole unit it from the track.
3) Unplugged the cable connected to the ice maker.
4) Using the phillips screw driver to remove the 3 screws. Carefully pulled out the ice module and installed the new ice module.
5) Put the ice maker back to the freezer, plug the cable back to the ice maker and put the clamp and tighten the nut.
6) Plugged the power cable back to the wall.
The first ice I got in an hour and a full bucket of ice in less than 24 hours. I spent less than $80 for the whole thing. Thank you so much Partselect for the great service and the stories posted, it really helped me to get it done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from WALLA WALLA, WA
- Parts Used:
- WPW10300024
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
original ice maker would make ice and then water would over flow into ice bin and freeze
first of all,i just want to thank parts select for sending me a second ice maker at no charge.after installing the first one and it didn't work,i talked with Heather and she sent me a new one.installation went the same as before.hardest part is getting the quick connect wire harness apart and the ice fill arm .it is working great and my home is happy.thank you!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary Petresky from Bethlehem, PA
- Parts Used:
- WPW10300024
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Ice maker not producing ice
Customer service provided a video of the ice maker removal and installation. I watched the video and performed the remove and replacement.
Simple task.
Shout out to the customer service person, OUTSTANDING SERVICE. I apologize for not getting her name, great job.
Simple task.
Shout out to the customer service person, OUTSTANDING SERVICE. I apologize for not getting her name, great job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bart from Ocean View, DE
- Parts Used:
- W11396037
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Very easy, made a huge difference
Took off the old gasket and pushed in the new one.
Note on the left door, you will need to remove the center piece. suggest watching youtube video.
Note on the left door, you will need to remove the center piece. suggest watching youtube video.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Galen from WASECA, MN
- Parts Used:
- WPW10196393
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Fresh Food Compartment occasionally going down to 28-30 degrees F
Failure detected as Damper Control at upper rear of compartment would continuously open/close, would never stay open or closed. Sometimes the main board would turn it off (maybe a low thermistor limit?), but it would stick open a bit, and keeping letting freezer air into fridge. Could have potentially been control board, but as it turns out after disassembly of the defective damper, the internal microswitch was stuck in the closed position so it wouldn't shut off the motor. Easy fix by gently pulling the cover off the damper control, pull out Styrofoam encasement, then a phillips to remove the damper assembly. Gently push tabs to release wire connectors. Reverse the process and you're done! If I really wanted to go on the cheap, I could have just changed the microswitch, but that looked like a shaky maneuver at best. This site saved me on this one, so happy to share my experience with this Maytag and its nasty habit of freezing my milk and eggs!! :)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Geraldine from MUNDELEIN, IL
- Parts Used:
- W11395888
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
Did not need filter
Unscrew filter. Screw on filter bypass
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from WESTERVILLE, OH
- Parts Used:
- W11658402
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Broken black plastic spring mechanism inside freezer rail
Remove rail and removed broken black plastic spring mechanism with new one and then replace rail.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Estel from Luling, TX
- Parts Used:
- WP67003638
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers
RH door closure broke
Removed the door and replaced the broken door closure bushing. I had courteous help and responce from Parts Select people. Excelent turn around time on parts delivery.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Phoenix, AZ
- Parts Used:
- WPW10300024
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Ice jammed on exit from ice maker
Removed old ice maker. Unscrewed unit from slide. Unplugged old wire. Screwed on new unit. Replugged in wire. Slid ice maker back into refrigerator and all worked properly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JOE from FORT WAYNE, IN
- Parts Used:
- W11396037, WPW10443321
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver
Mold build up and moisture on gaskets and door
Placed new gaskets on hot patio to smooth them out. Took minion bar off and removed door gaskets. Replaced new gaskets, and minion bar.
Took freezer door off and replaced gasket. I had problems with the first set of door gaskets but customer service replaced them in record time. Service was outstanding. 5 Stars
Took freezer door off and replaced gasket. I had problems with the first set of door gaskets but customer service replaced them in record time. Service was outstanding. 5 Stars
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sonny from WHITESTOWN, IN
- Parts Used:
- WPW10300025
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Ice maker not making ice.
Removed old ice maker by removing 3 screws, unplugged wiring harness. Replaced with new ice maker, placed three screws back to secure the ice maker, plugged wire harness back, and product is working well at this time.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Keith from OLYMPIA, WA
- Parts Used:
- WPW10196393
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Noisy damper
Easy fix, it's right in the back of the fridge under a cover that just clips in, a piece of foam, and two screws. The hardest part is getting the clips free without breaking them. After replacement it's silent instead of making a grinding noise regularly.
Was this instruction helpful to you?
Thank you for voting!