GI6FARXXB00 Whirlpool Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Empty box sent with no part!!!! No customer service help because of covid
No product was sent in the box for the shaft I received an empty box from them cannot perform any repairs because I got no product from this company. Called customer service said due to Covid no customer service available when online and receive no customer service no refund no product no help
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- EMILE from RACELAND, LA
- Parts Used:
- WPW10326469, WP67003854
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Too much weight on shelf over time caused it to crack down middle
Removing the old pieces & figuring out how to separate the front trim so it could be reinstalled on the new frame took the longest! (released the securing tabs with a screw driver). Reinstalling the new parts were straight forward, "no problem". (epg)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeffrey from Lexington, KY
- Parts Used:
- 8201515
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
The icemaker would not produce ice because the motor that pushed the cubes out had failed. The original icemaker failed in this way and we had the icemaker replaced by Sears Service for about $200. The second icemaker failed for the same reason after 18 months. I decided to do the repair myself t
Open the refirigerator door and push and hold the On/Off button at the top to turn off internal power. Open the freezer door and move the icemaker switch on the right side freezer wall to "off".
To get access to the icemaker, first remove a hinged plastic door that mounts to the ceiling of the freezer compartment by two hex screws. Remove the screws and the door so you can work with the icemaker without interference.
The icemaker assembly will slide out once the wireharness has been disconnected. To disconnet the wire harness, a while plastic shield has to be removed from the right side of the icemaker, just behind the water inlet.
Locate a hex screw on the bottom right rear of the icemaker and remove it with a socket wrench. Then the plastic cover can be pulled off.
Slide the icemaker out enough so you can get your fingers on the plug connector. It takes some effort to pull the plug connectors apart. Once unplugged the whole icemaker assembly can be removed.
The motor module is located on the left side and is protected by a white cover. This cover is not attached so it can be pulled off to reveal the motor module.
Remove 3 screws from the outside of the motor module and the module can be pulled out of the housing. Insert the new motor module. The module turns the shaft of the ice srapper arm. the shaft has a D shape which mates with the hole in the motor module so you may have to roatate the scrapper arm until the shaft shape matches up with the hole shape in the motor module.
Once the motor module is seated, replace the 3 screws and push the white cover back on.
Position the icemaker so you can reconnect the wireharness plug connectors. Once connected you can push the icemaker asembly back into the grooves of shelf rail. Reattach the while protector shield which covers up the wire harness plugs.
Open the refirigerator door and push and hold the power button to turn internal power back on. Move the icemaker switch on the right wall of the freezer to the "on" position and close the door.
The icemaker should start making ice within 2 hours.
To get access to the icemaker, first remove a hinged plastic door that mounts to the ceiling of the freezer compartment by two hex screws. Remove the screws and the door so you can work with the icemaker without interference.
The icemaker assembly will slide out once the wireharness has been disconnected. To disconnet the wire harness, a while plastic shield has to be removed from the right side of the icemaker, just behind the water inlet.
Locate a hex screw on the bottom right rear of the icemaker and remove it with a socket wrench. Then the plastic cover can be pulled off.
Slide the icemaker out enough so you can get your fingers on the plug connector. It takes some effort to pull the plug connectors apart. Once unplugged the whole icemaker assembly can be removed.
The motor module is located on the left side and is protected by a white cover. This cover is not attached so it can be pulled off to reveal the motor module.
Remove 3 screws from the outside of the motor module and the module can be pulled out of the housing. Insert the new motor module. The module turns the shaft of the ice srapper arm. the shaft has a D shape which mates with the hole in the motor module so you may have to roatate the scrapper arm until the shaft shape matches up with the hole shape in the motor module.
Once the motor module is seated, replace the 3 screws and push the white cover back on.
Position the icemaker so you can reconnect the wireharness plug connectors. Once connected you can push the icemaker asembly back into the grooves of shelf rail. Reattach the while protector shield which covers up the wire harness plugs.
Open the refirigerator door and push and hold the power button to turn internal power back on. Move the icemaker switch on the right wall of the freezer to the "on" position and close the door.
The icemaker should start making ice within 2 hours.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mario from EL PASO, TX
- Parts Used:
- WP67006331
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
the locking latch to the water filter cover had been broken for a while
Open the existing cover and carefully with the thumb and index fingers, pry the cover at over the left pin and remove the cover. Place the replacement onto the right pin and pry the left placing it over the left and you are done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Geraldine from LANOKA HARBOR, NJ
- Parts Used:
- WPW10326469
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Plastic bar between drawers cracked on the end
Removed glass shelf and inserted plastic running bar for drawers
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Connie from HESPERIA, CA
- Parts Used:
- WP67003854
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The crisper frame itself was broken in the back little tab
I just watched the YouTube video that you guys provided and did it exactly step by step and it was perfect
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from ALIQUIPPA, PA
- Parts Used:
- W11396037
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Gasket torn
Pulled old gasket off door put new one in channel on door pushed gasket in channel less than 10 minutes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Billy from EVERTON, AR
- Parts Used:
- WP12204826
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Broken glass shelf
Replaced with no problem
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from PHOENIX, AZ
- Parts Used:
- WPW10326469
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
insert new drawer divider
Just removed drawers and glass plate. Put in divider and replaced drawers and glass plate. I was done in 5 minutes. no tools required.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Howard from POUGHKEEKPSIE, NY
- Parts Used:
- WPW10212139
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Had a cracked bin and replaced it with the new one...
Removed as said cracked bin and replaced with one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Allentown, PA
- Parts Used:
- WPW10312696
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
not making ice
watched video
took me less than 5min. to replace inlet valve.
an cleaned my frig at the same time that took me longer to do.
took me less than 5min. to replace inlet valve.
an cleaned my frig at the same time that took me longer to do.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Fairview Heights, IL
- Parts Used:
- 8201515
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Ice maker wouldn't cycle
Originally I took the module off and found that a small plastic part had broken. Both pieces were still there, so I super glued them together and reassembled the unit. It worked great for a couple months. I realized it needed a more permanent fix, so I found the model # and looked up the part. That was very easy on your website. I ordered the part expecting it to take 4-7 days. It was at my house in two days! 15 minutes later I was makin' ice, and makin' my wife happy. Thank you for an all around great experience. I'll definitely buy from you again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from Paola, KS
- Parts Used:
- WPW10498990
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Wrench set
crack in inlet valve
took old inlet valve off put new one on hooked up ice maker
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Angela from Topeka, KS
- Parts Used:
- WPW10534153
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Refrigerator was missing grille
This grille just snapped into place without the use of tools. Couldn't have been easier. And the delivery was super fast; I ordered online one day and the item arrived the very next day.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rodney B. from Crestview, FL
- Parts Used:
- W11395888
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Filter stopped up. Causing the refrigerator to make a loud noise. water dispenser didn't work. less than 4.00 fixed all that
Shut off water supply. filter is located in the upper right hand corner of the refrigerator on the inside. open the drop-down door. by hand pull the filter downward. then twist it to the left one quarter turn. it should pull out. I replaced it with a filter bypass plug. you can purchase a high quality filter to replace.it don't buy cheap filter.I made that mistake! hope this helps good luck!
Was this instruction helpful to you?
Thank you for voting!