GI5FSAXVB00 Whirlpool Refrigerator - Instructions

Replaced mullion and pivot block
The pivot block and the mullion showed signs of wear and tear where they would meet up to close the left door.

I was hesitant to remove old seal, after I removed, I lined up new seal, and the seal popped into the slots very easily. Easy repair, no tools, worked great. The seal takes about 24 hour to seat itself for a great fit.

Placed new gaskets on hot patio to smooth them out. Took minion bar off and removed door gaskets. Replaced new gaskets, and minion bar.
Took freezer door off and replaced gasket. I had problems with the first set of door gaskets but customer service replaced them in record time. Service was outstanding. 5 Stars

Checked if the cube maker still worked by putting some water in - yes!
Jumped the old valve to see if it would release water and nope.
Replaced the valve and everything is great.

You supplied the right part, the repair was simple and everything is working. No expensive repairman.

Since it wasn't possible to squeeze the seal in between the door groove and the bar which closes the gap between the two doors, I cut the seal side in half and snaked it in from the top and the bottom. Since the cut is behind the bar when the door is closed there is no compromise in getting a good seal around the door. Note there was no apparent way to easily remove this bar.

one screw and electric plug and the unit slide out. Slide the new one in and your ready to go.

Layer it out for 24 hrs used hairdryer on med for the wrenkles.

Instructions were great five minutes to remove and replace fan....Thank You............ saved big money

I initially tested the heating element and defrost thermostat using an ohm meter. the defrost thermostat was incased in ice, so I replaced it first. The refridgerator worked for about a week and then froze up again. I then replaced the thermistor and the unit is working as designed.

Googled "intermittent clicking noise" or something similar and consensus was it was either the capacitor or compressor start relay. You-tubed videos on how to replace these. Looked easy. Just unplug them from the condenser and replace. Contacted Part Select and staff said 50% of the the time it was the capacitor, 50% of the time it was the relay. I was in a time crunch so I ordered both and they came in a couple of days. I replaced the capacitor but the clicking noise continued. I replaced the relay and problem solved! Maybe I could have gotten away with just replacing the relay, but I had them both by then and figured with a 10 year old fridge, better replace them both at the same time and be done with the problem. So far, so good.

Watched video. Unplugged refrigerator and popped out switch. In plugged connector and pushed switch in place. Plugged in refrigerator and the light worked

The old cover was off and I just slid the replacement part that I got from you'll, it just slid in place and snapped close. Perfect fit. Thanks guys

Unplug power to refridg/freezer. Removed the screw in rt. rear bottom of ice maker to remove. After removing slightly, unplug pigtail. Remove ice maker completely. Remove large square cover from left side to expose motor. Remove screws to remove motor. Replce with new. Replace ice maker to freezer, plug pigtail back in, put screw back in rt rear bottom, plug refridg/freezer back into power source. Ice was making in about 2 1/2 hours.

Prior to ordering I removed freezer panel and checked for ice build up and fan functionality. Then removed rear panel cleaned lint from everything pulled front panel vacuumed out the condenser. Plugged back in and all seems to work with the exception of compressor. I have a little experience so googled in model number and your site popped up. I looked up part and the site gave me a percentage loved that. I ordered wish I would have rushed shipping as took about 10 days. Installed in less than 30 minutes and all runs great ??

Open and remove door by loosening two screws on both sides of the door. Lift up and away the door.place the door on flat surface, grab and lift up on seal pulling out of reach. Clean track, alone seal on food before pressing in place. Check to make sure seal is set in place. Install door job done.