GI6FARXXQ05 Whirlpool Refrigerator - Instructions

This took 30 seconds. Lift out shelf glass, remove broken pieces, snap new part into place.

Removed old gasket by carefully pulling it out of the retaining groove. Installed the new gasket starting the corners first and then seating the upper and lower straight portion gently in the retainer groove. Total time for installation was at most 5 minutes. After a week no ice or frost has been found along the bottom of door or freezer. Note: the new gasket came in a small box for shipping purposes and the new gasket was twisted in a v for this purpose. Upon arrival, I laid it out flat on table overnight so it could cool to room temperature and straighten. I would recomend this procedure for a perfect installation.

Followed instructions for testing and replacement on You Tube video.

The replacement part provided was not an exact replacement. The part did not include a water reservoir. Instead, it had a 25 ft long water line that ran from the water filter to the water connection behind the fridge. The long water line was difficult to deal with, did not fit easily into the space provided for the water reservoir, and is coiled up behind my fridge. The part did work, but I'm unhappy with not having the resevoir.

Took out the old and installed the new.. The fit was perfect.

Took off the old gasket and pushed in the new one.
Note on the left door, you will need to remove the center piece. suggest watching youtube video.

Failure detected as Damper Control at upper rear of compartment would continuously open/close, would never stay open or closed. Sometimes the main board would turn it off (maybe a low thermistor limit?), but it would stick open a bit, and keeping letting freezer air into fridge. Could have potentially been control board, but as it turns out after disassembly of the defective damper, the internal microswitch was stuck in the closed position so it wouldn't shut off the motor. Easy fix by gently pulling the cover off the damper control, pull out Styrofoam encasement, then a phillips to remove the damper assembly. Gently push tabs to release wire connectors. Reverse the process and you're done! If I really wanted to go on the cheap, I could have just changed the microswitch, but that looked like a shaky maneuver at best. This site saved me on this one, so happy to share my experience with this Maytag and its nasty habit of freezing my milk and eggs!! :)

Pop off vent cover remove 2 screws removed cover housing and foam. Removed damper by unclipping tabs on left and right side of control lift up and out. Unplugged power wires reinstalled in reverse order.

Easy fix, it's right in the back of the fridge under a cover that just clips in, a piece of foam, and two screws. The hardest part is getting the clips free without breaking them. After replacement it's silent instead of making a grinding noise regularly.

Unscrew filter. Screw on filter bypass

Removed the door and replaced the broken door closure bushing. I had courteous help and responce from Parts Select people. Excelent turn around time on parts delivery.

Remove rail and removed broken black plastic spring mechanism with new one and then replace rail.

Placed new gaskets on hot patio to smooth them out. Took minion bar off and removed door gaskets. Replaced new gaskets, and minion bar.
Took freezer door off and replaced gasket. I had problems with the first set of door gaskets but customer service replaced them in record time. Service was outstanding. 5 Stars

I was hesitant to remove old seal, after I removed, I lined up new seal, and the seal popped into the slots very easily. Easy repair, no tools, worked great. The seal takes about 24 hour to seat itself for a great fit.

For this repair, the following YouTube video was most helpful in showing how to remove the ice maker from the refrigerator model that I have: for some reason this site has deleted my video cite but it is the YouTube video cite that ends in 7HHH03SFdCA Next, because the electrical wiring harness part has changed since production, and the new ice maker part comes with two different harness' (you have to determine which one is most similar to the harness that you remove), take a lot of pictures of the old wiring harness before removing it. There are a lot of different wires that need to be reconnected. There was a prior post by "Greg from Aliso Viejo, CA" that I printed out and followed--that post was also very helpful.