G25EFSB2313 Whirlpool Refrigerator - Instructions

I broke the left side end cap the holds the pantry door on.
I search the internet for the part and happened to run across part select. I order the part and received the part with in 3 business days. It took less than 30 minutes to replace the end cap.

The great reviews help me with my choice to order the part from part select. I will order parts from them again.

Thanks for helping me fix my fridge.

Unplug ref then remove lower(freezer) panel plus trays and thermistor’s cover/holder then remove the evaps cover. I found the evaps all frozen up. Cut and remove old thermistor, strip wires 1/2 inch then cut the new thermistor wires to length and strip 1/2 inch, use the enclosed insulated crimp type connector and put back everything in the reverse order. It works great afterwards.

Broken bottom drawer lid mount

After removing the shelves and drawers to gain access to the End Cap unit. I removed the screws and detached the unit which was a little tricky without any actual drawing details. After removing the unit I had to undo the plastic temperature control arm without breaking same. I then transferred the shelve draw slide and reconnected the control arm assembly to the new End Cap unit . At that point it was a simple installation, the drawer works better then new. Note: I did find some loose packing material behind the End Cap assembly unit that might have caused the failure of the drawer and door mechanism during its original factory fabrication. Other than that the project was a complete success. Dick S.

take out two nut driver screws remove piece, take off track two philips head screws. transfer temp control rod, really easy then put track back on and install piece. probable took as long to remove the two veg crispers and glass top. this is a very easy fix. i did notice that the pin on the original was about 3/8 of an inch forward so flapper door did not quite line up and im sure caused the pin to snap off. the replacement part, the pin is exactly the same position as the other side. i believe the original was defective from the mfgr.

Took off old cover 3 screws...removed metal track and 2 other plastic sliding bars for air flow..put on new cover and carefully put back deli cover on plastic pins..easy fix...lousy design by maytag again! Thanks to PartSelect easy and prompt service and delivery!

Used a screw driver to pull old switch. Pulled one wire at a time, only two wires. After wires instlled to new switch push new one back in place where the old one was.

I simply removed the old switch using 2 small screwdrivers and the old switch case popped out. I then upluged the wires from the old switch and reversed the process. Didn't take longer than 5 minutes begining to end! Thank you for the great service! Duncan quaid

There was little or almost nothing to change out the End Cap, two screws on the End Cap and two screws on slide. It took longer to removed and replace the two drawers and shelve than it did to replace the End Cap. The part I ordered was exactly what I needed.

Popped off the control panel at the top behind the door. Found the thermistor and replaced it, cutting the wires and splicing the new one in. Immediately the warm section of the refrigerator was getting below freezing temperature readings, so the cooling vent was not opening. I put the old one back on and the temperature readings went back to being accurate. So this was not the problem. I believe now that the fan somehow is not blowing enough cold air up. So now I'll probably buy a fan motor and maybe a blade and try that. Otherwise the computer module I priced at $500 so I hope it isn't that. I replace the fan motor a few years ago already.

The repair was very simple, you just remove the existing part that is held in place by two holes in the lid and insert the new lid. very easy.

Unscrew filter. Screw on filter bypass

Heated new gasket in dryer. Removed old gasket. Took less than five minutes per door and I am 78 years old!

Removed the old gasket by pulling it out of the groove and installed the new gasket using my fingers to push the gasket into place.

Very simple--Just remove all drawers, remove old end cap, remove slider from old end cap and put on new one. Screw on new end cap and replace drawers. Took about 10 minutes.