G20EFSB2313 Whirlpool Refrigerator - Instructions

I bought a set of appliances used online and the fridge door did not align to the other door. I quickly noticed I had lost the lower bushing to the right door upon transportation so I did what any man would do...find a way to fix it! after checking out a few websites I ran accross Partselect and after seeing their "dummy proof" diagrams It was certain I couldn't mess this up considering the loads of bushings to choose from. The order was placed Monday morning and to my surprise I had a package the VERY NEXT DAY!! AMAZING delivery time and quality products. PartSelect is definately my appliace parts source from now on! Thank you!

I called the installer of my filter unit and he told me that often, thhe fridge filter is the problem. Like magic it worked

It was so easy!

Thanks for the rush to my home on the part.

I just unscrewed the plate that locks in the light switch (screwdriver) and unplugged the old faulty part and plugged in the new switch, screwed the cover back on and I was done!

Easy!

And I am not Mr. Fix-it!

1. removed both bottom crisper drawers
2. removed glass shelf under crisper drawers
3. removed shelf support pieces
4. removeded snack drawer
5. removed left slide rail using phillips screwdriver (2 screws)
6. removed LH end cap using socket wrench (3 screws)
7. attached new LH end cap
8. attached slide rail
9. installed glas shelf supports
10. installed glas shelf
11. install bottom crisper drawers
12. install snack drawer
13. install snack drawer top

total time was less than 15 minutes

you need to take the deli drawer out, make sure your flat head screw driver is large enough for the head of the screw as screwing into the plastic is a bit difficult. Other than that there are 2 screws and its pretty easy.

Removed the three screws that held part, lifted and removed old part and replaced with new piece.
Couldn't have been easier. Saved me the $100 the repair man quoted me. Cannot believe it was so easy and the
part was soooo affordable! Thank you very much for the speedy delivery. It came within days of my order.
I will use your service again for sure!
Thank you!
Allyn Rosenzweig

The front had to be removed from old drawer a put on new one

Unplug ref then remove lower(freezer) panel plus trays and thermistor’s cover/holder then remove the evaps cover. I found the evaps all frozen up. Cut and remove old thermistor, strip wires 1/2 inch then cut the new thermistor wires to length and strip 1/2 inch, use the enclosed insulated crimp type connector and put back everything in the reverse order. It works great afterwards.

Used a screw driver to pull old switch. Pulled one wire at a time, only two wires. After wires instlled to new switch push new one back in place where the old one was.

Replaced filter and the water started to flow like the Nile River and the ice maker came back to life.

1. Remove all drawers {3}, shelves {glass 1}, shelf support {1}. 2. Remove two {2} screws from End Cap. 3. Carefully remove End Cap and drawer temperature control part on the back wall keeping them aligned as installed. The part on the back wall swings out so that the tab on the left end of the piece may be withdrawn from the securing slot (hole). The two parts should be carefully removed while keeping the two parts at a right angle the way they are installed. The reason for this caution follows. 4. On the back side of both parts are plastic pieces that, I believe, can be easily broken if you are not aware. The pieces are connected together at the right angle. They are the control arms for the temperature control -- on right side End Cap only -- the left side doesn't have them or the rear part on the back wall. 5. The pieces must be disconnected and removed. You must examine and ponder how they are held in place and hooked together in order to disconnect and remove them without damaging them. The same advice is applicable to reinstalling the pieces in the new part -- End Cap. 6. After reassembled and keeping the two parts at a right angle, insert the tab on the left end of the back wall part into the slot (hole) and swing the two parts back into position. 7. Replace the screws. 8. Done, reinstall the shelf, shelf support, and the drawers. NOTE: I ordered the two screws but they were not needed.

First, make sure you have the correct part. I had trouble with mine, at first, until I realized that I had received the wrong part... it was same shape but larger. To begin, remove both fruit/vegetable drawers. Remove deli drawer. Remove deli drawer glass panel with both supports. Remove 3, 1/4" hex screws that attach end-cap. Disengage temp control slide and arm from end-cap by carefully moving parts in the direction where they will disengage. Remove temp control slide from end-cap. Now that end-cap is out, remove 2 screws that hold metal drawer slide to end-cap. Attach drawer slide to new end-cap. Attach temp contol slide and connect the plastic arm. Attach end-cap to refrigerator. Replace glass shelf, supports and drawers. Done.

1. Turn your water OFF and pull the refrigerator out from the wall so you can access the back.
2. Use pliers to remove tubing clamp.
3. Remove old water fill tube.
4. I used a putty knife to gently pry out the old fill tube from the back of the refrigerator. Once the fill tube pulls out about 1/4 to 1/2", then you can gently pull the remainder of the tube out by hand. Once I removed my "old" fill tube, that is when I saw the "ice plug" that was causing pressure in the water supply line and caused my water line to pop off.
5. Install new fill tube. The end that goes in first needs to go through a small "ring" inside the freezer (this "ring" is not encountered until the fill tube only has about one more inch to be inserted into the back of the refigerator. I could barely see this "ring" if I opened the freezer drawer and stuck my head in as far as I could. I had to gently rotate the new fill tube until it cleared the "ring". You will feel some resistance until it lines up properly.
6. Snugly push in the part that stays on the outside of the refrigerator until it looks like it is sealed.
7. Gently push up the water fill tube where it belongs in the new part and replace the tubing clamp.
8. Turn your water on and make sure there are no leaks (I left my refrigerator out for about an hour).
9. Push your refrigerator back in place.

I simply removed the old switch using 2 small screwdrivers and the old switch case popped out. I then upluged the wires from the old switch and reversed the process. Didn't take longer than 5 minutes begining to end! Thank you for the great service! Duncan quaid

Replaced the left side endcap for the drawer. Three screws and it popped out. Easy process once I actually looked at it. Drawer cover now works as designed. Replaced inline water filter. Not problem there.