7GI5FSAXVY2 Whirlpool Refrigerator - Instructions

It is as easy as is shown in the self-help video. (1) Disconnect the power, (2) Roll the appliance out so you can get to the back, (3) Using a nut driver remove all the screws from the lower back panel then remove the panel, (4) Remove the tensioner wire, (5) unplug the electrical connection to the capacitor, (6) gently but firmly remove the capacitor and starter relay as one unit, (7) preassemble your new capacitor and starter relay as one unit, (8) now simply reverse your steps for installing and you are done! These two parts saved me the cost of a new refrigerator. Almost as easy as changing a light bulb. PS: while you have the panel removed you can do a thorough cleaning with a soft brush and vacuum.

Unlug refrig or turn off refrig from its control panel On/OFF switch.
For ease of work remove freezer shelve directly below the ice maker. Remove four screws from the bottom of the ice maker assembly, three that secure the ice maker and the other that holds a plastice shroud in place over the ice maker's power plug.
The ice maker is now ready to be removed; it will slide forward by pushing up on left and right side of the ice maker's mounting slide rails. Once the ice maker is moved forward it is easier to disconnect its power plug (depress a locking tab on the side of the connector and pull connector apart and remove ice maker assembly.
Remove and replace motor module by removing three screws and and replace with new unit.
Reverse ice maker removal proceure for installation. Once installation is completed turn on Power to Refrig, Ice making should begin after a few hours.

Removed old gasket by carefully pulling it out of the retaining groove. Installed the new gasket starting the corners first and then seating the upper and lower straight portion gently in the retainer groove. Total time for installation was at most 5 minutes. After a week no ice or frost has been found along the bottom of door or freezer. Note: the new gasket came in a small box for shipping purposes and the new gasket was twisted in a v for this purpose. Upon arrival, I laid it out flat on table overnight so it could cool to room temperature and straighten. I would recomend this procedure for a perfect installation.

Took out the old and installed the new.. The fit was perfect.

Replaced filter and the water started to flow like the Nile River and the ice maker came back to life.

The troubleshooting time takes about 20 to 30 minutes. After checking out the solenoid (valve water), the water line, and the electronic board (emitter/receiver) are working fine. The only thing left is the ice module. I called Partselect and talked to a sale rep to make sure I get the right part, and the lady was so helpful by sendind the picture of the part so I can review before ordering it. I received the part in 3 days ( normal shipping) and did the folowings:
1) Unplugged the power cord from refrigerator.
2) Removed the ice module by removed a 1/4" screw from under the right side of the icemaker that retains the icemaker and a “U” plastic clamp and then pull out the whole unit it from the track.
3) Unplugged the cable connected to the ice maker.
4) Using the phillips screw driver to remove the 3 screws. Carefully pulled out the ice module and installed the new ice module.
5) Put the ice maker back to the freezer, plug the cable back to the ice maker and put the clamp and tighten the nut.
6) Plugged the power cable back to the wall.

The first ice I got in an hour and a full bucket of ice in less than 24 hours. I spent less than $80 for the whole thing. Thank you so much Partselect for the great service and the stories posted, it really helped me to get it done.

Once I realized the High voltage Board was bad I ordered the new High voltage board from Parts Select, the part was in stock and was delivered to my house in two days, I opened the box, and the instructions were very clear how to install the new high voltage board and program the board with the code for my refrigerator. There are also videos on You Tube on how to program the code on the refrigerator in case you have difficulty. In all, the problem was fixed and the refrigerator was up and running. Thank You Parts Select.

Unscrew filter. Screw on filter bypass

Remove rail and removed broken black plastic spring mechanism with new one and then replace rail.

Checked if the cube maker still worked by putting some water in - yes!
Jumped the old valve to see if it would release water and nope.
Replaced the valve and everything is great.

You supplied the right part, the repair was simple and everything is working. No expensive repairman.

Layer it out for 24 hrs used hairdryer on med for the wrenkles.

We removed the old switch, unplugged it, plugged the new one in and it was easy to do. But when we tried to put the switch back in we had a very hard time doing it. Eventually got it in, but if it had not been for the difficulty we had getting the new switch to snap in to place, it would have taken under 5 minutes.

Since it wasn't possible to squeeze the seal in between the door groove and the bar which closes the gap between the two doors, I cut the seal side in half and snaked it in from the top and the bottom. Since the cut is behind the bar when the door is closed there is no compromise in getting a good seal around the door. Note there was no apparent way to easily remove this bar.

Very easy. Just get hold of the gasket with your strong fingers and pull it out of the groove it is in. Clean the groove, I used Windex and paper towels. On the new gasket there are 2 wide areas on the vertical part. these must be facing toward you and on the handle side of the door. start at the tor center of the door and work the gasket in with your fingers outward to the corners then work on the bottom of the gasket in the same manner, then start on the vertical gaskets. when you think every thing is aligned take your thumbs and press very hard all around. You may have to repeat.

Remove back cover
Remove drip thing from top to tray in the back
Remove fan motor assembly. This is squirrely. Top bends towards you, bottom pushes in to the unit. Not fun.
CAREFULLY remove copper tube that rests on drip tray
Remove tray - there are clips in the front that get released by screwdriver
Clean up
Replace new tray
Replace copper tube
Play with fan motor assembly till it fits. It doesn't look like it's gonna work until it does. See youtube videos on this.
Replace drip thing from top to tray - I forgot this one the first time.
Replace cover.

This is a simple, but squirrely, repair. Right on the border of easy (because so few tools and steps) and A Bit Difficult because of the patience required.