4ED20ZKXFN00 Whirlpool Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Glenn from ALEXANDRIA, MN
- Parts Used:
- WP2188656
- Difficulty Level:
- Difficult
- Total Repair Time:
- Less than 15 mins
wrong draw er frist time
very good
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bart from Salt Lake City, UT
- Parts Used:
- 4318165
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Refrigerator door wouldn't close on it's own anymore
All I had to do was remove the screws at the top of the refrigerator door that hold the top hinge and once that was done I lifted up on the door and it came off. I then flipped the door upside down and was able to replace the door cam on the door and the other cam on the bottom hinge of the refrigerator. Once replaced, I put the door back on and put the screws back in on the top hinge of the refrigerator door. Works great now!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jenice from Angleton, TX
- Parts Used:
- 4388538
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench (Adjustable)
shelf had no support
inserted stud and twisted
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- wendy from palm coast, FL
- Parts Used:
- W11581579
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Shelves in freezer falling off
Went online with the model number, the part was very easy to find, diagrams helped me to have confidence in the choice. Parts came in two days, tore them open and used a screw driver to replace the broken shelf brackets, replaced shelves, I am a happy camper!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- CHARLES from INDIANAPOLIS, IN
- Parts Used:
- WP2196190
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Replace two broken Door Shelf Retainer Bar End Caps
To get the broken end cap off of the retainer bar, hold the retainer bar still and pull the broken end cap straight off on a line that is parallel with the retainer bar, and with a little tugging. Might even have to tap the end cap lightly. Slide the new cap back on to the retainer bar and then put the end cap back into the door slot by putting the bottom of the end cap into the slot first by tilting the upper part back a little, then pushing down on the end cap to get it down into the slot far enough to let the upper part go in. Then adjust the end cap up slightly to cause it to snap into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from Santa Rosa, CA
- Parts Used:
- 4318165
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers, Wrench set
Door closing cams worn on bottom door hindge
1, Removed heavy items from door bottom two shelves.
2. With door closed, prop up door with 2x4 boards and wood shim to support door weight.
3. With nut driver, wrench or socket wrench remove lower door hindge.
4. Removed worn plastic door cams and shim.
5. Install new door cams and shim.
6. Install lower door hindge and lubricate cams with silicone grease.
7. Remove wood bracing.
2. With door closed, prop up door with 2x4 boards and wood shim to support door weight.
3. With nut driver, wrench or socket wrench remove lower door hindge.
4. Removed worn plastic door cams and shim.
5. Install new door cams and shim.
6. Install lower door hindge and lubricate cams with silicone grease.
7. Remove wood bracing.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marge from Alliance, NE
- Parts Used:
- 4388538
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
Broken off from over loading
My husband twisted the stud off and was able to put the new ones in quickly
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wm. from Naples, FL
- Parts Used:
- WP2198202
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Unit would freeze then defrost but not go back into freezing again untill I moved the thermostat
Turn off power .Remove the control knobs and pry off the front panel ,it just snaps on,Take out two screws holding the control panel Take out the two screws holding the control to the base of the panel to get at the two screws holding the control to the bracket. Ther are screws holding the covers over the thermostat tube. Then pull out the tubbe and remove the plastic cover on the old control and place it on the new control tube. Then route the new tube into the snaps be careful to not make ant sharp bends in tubing.When that is done fasten the control to the bracket and fasten the bracket to the panel.Replace covers over tube to hide it and keep from damaging it when putting things in fridge.. Mount the conrol bracket back to the fridge and replace snap on cover. Plug in electric.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ouida from LORMAN, MS
- Parts Used:
- W10508993
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Tray missing
Simple fix. I watched the video it was great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from SENECA, SC
- Parts Used:
- WP2188656
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The original drawer had chipped along the glides and would not close properly
The refrigerator had to be pulled away from the wall far enough to permit the door to open fully, but no tools were needed and no difficulty was encountered. Removed the old drawer and discarded it. Inserted the new drawer and closed the humidifier vent. Pushed the refrigerator back in place. Job done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bruce from MONTGOMERY, AL
- Parts Used:
- WP3400012
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Refrigerator door not closing properly
We’d had the refrigerator repaired a year ago by the service department of our local appliance store. Turns out the service tech somehow used the wrong screw when replacing the door cam, causing it to rub on the cams and causing premature wear. After watching the provided repair video, it took about 10 minutes to remove the door, replace the cams and reinstall the door. Saved well over $100 and had the job done right this time.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michelle from NASHVILLE, TN
- Parts Used:
- W10864399
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Glass shelf shattered
Just opened the package and drop into tray frame
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Denis from CLIO, MI
- Parts Used:
- WP2196189
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
The retainer end caps had broken.
Pull the broken end caps out and snap the new ones into place. Very easy repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from INNSBROOK, MO
- Parts Used:
- 4386774
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
One of the front wheels was broken in half.
Very easy. Left the front of the refrigerator so it is approx. 4 inches of the floor. (used a two by four. Removed the screws (one for each roller). Removed the rollers and replaced with new rollers. Reinstalled the screws with secures the rollers to the refrigerator. Done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from ATHOL, ID
- Parts Used:
- WPW10329686
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
door would not close properly
removed screw on top cover emptied ref door remove 3 top screws holding bracket on top. lifted the door then remove old cam then reassembled.
Was this instruction helpful to you?
Thank you for voting!