4ED20ZKXFN00 Whirlpool Refrigerator - Instructions

Removed cheese & cold cut drawer accessing lower crisper drawer glass missing from surrounding frame.
Dropped in glass into grove of crisper frame…Reinstalled (sliding)!above cold cut drawer in its position and the same for crisper drawer..Finished!!!
All good except for $110.00 price tag for a piece of glass

easy - remove the door, replace th part, put back the door

Slid the old drawer out and slid the new drawer in. Less then a minute!

I did some tests and determined that the tub-to-pump drain hose had a leak in it.I then looked on the web to find disassembly instructions. I have a stacked washer dryer combination in a very confined space. The repair involved disconnecting both the washer and dryer from the water, gas, electric and venting systems first, then unstacking the dryer from the washer (not so easy, it required a helper). The machine was then pulled out so I could get at the parts necessary to remove the outside components and sheet metal. Then, I disassembled the top, front and access panel in the back. The disassembly went very well. I got access to the drain hose assembly and removed it fairly easily. I ordered a replacement drain hose assembly and found that installing the large port of the assembly was very difficult. (The two other ports were easy.) After thinking about it, I tilted the machine back a bit so I could try it from the bottom. That worked fine.I then reassembled and tested the machine. No leaks. Good luck with yours!

I just did what the instructions outlined and the job was done fast.

watched your instructions

Following the instructions on the site I removed the upper hinge cover and hinge(after removing the shelves from the door). I replaced both cams on the bottom hinge, reinstalled the door and the problem was solved. A couple of hints that may speed up the process: 1. On installing the door cam, I didn't get the holes in the door and cam aligned well due to a bit of interference from the metal tab on the door, so I temporarily inserted the upper hinge pivot in the bottom hole and retightened the cam. 2. I decide to re-align the freezer door . After this, the ice and water dispensers didn't work. Turns out the internal freezer light switch which also acts as a cutoff switch for the door dispensers wasn't being activated. Easy to adjust once the cause was discovered.

I read a previous entry that stated the stud needed to be twisted out, which was very useful. I was bit worried at first when I removed the broken one and a bit of the insulation came out and it seemed mangled inside, but twisting the new one in worked. It is in there firm and strong, good as original.

I follow the video From The Tech Guy ( Gentleman ). Thank you... Best Regards .Fco

just as the installation video show (very helpful) however the sheath tube that was pulled off of the old capillary tube did not go back on the new tube near as easy as the video showed. Got it on however and refrigerator is working like a champ now

Followed the video instructions.

Removed all of the food from the door by lifting the shelves out. Unbolted the top door hinge, and lifted the door off. Replaced the cam and placed the door back on, re-bolted the top hinge and placed all of the food and shelving back into the door. The door closes and seals when it is shut.

1, Removed heavy items from door bottom two shelves.
2. With door closed, prop up door with 2x4 boards and wood shim to support door weight.
3. With nut driver, wrench or socket wrench remove lower door hindge.
4. Removed worn plastic door cams and shim.
5. Install new door cams and shim.
6. Install lower door hindge and lubricate cams with silicone grease.
7. Remove wood bracing.

Turn off power .Remove the control knobs and pry off the front panel ,it just snaps on,Take out two screws holding the control panel Take out the two screws holding the control to the base of the panel to get at the two screws holding the control to the bracket. Ther are screws holding the covers over the thermostat tube. Then pull out the tubbe and remove the plastic cover on the old control and place it on the new control tube. Then route the new tube into the snaps be careful to not make ant sharp bends in tubing.When that is done fasten the control to the bracket and fasten the bracket to the panel.Replace covers over tube to hide it and keep from damaging it when putting things in fridge.. Mount the conrol bracket back to the fridge and replace snap on cover. Plug in electric.

My husband twisted the stud off and was able to put the new ones in quickly