3XARG495WP00 Whirlpool Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- David from GROVESPRING, MO
- Parts Used:
- W11384469
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
light did not work on the refrigerator side
bulbs were not burnt out. received the new switch in a few days. watch the short video, was good to see how it comes out. used a putty knife to release the defective switch, removed wires put them on the new one and posed the new switch back in. Not bad Part cost $11.00 7 dollars shipping so for 17 bucks it works great. nice to see what is inside the refer!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David Barnes from ROSWELL, NM
- Parts Used:
- W11384469
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Rocker on switch broke off
Eased the putty knife under the edge of the switch housing and pried it off. Pulled two wires off the old terminals and hooked them onto the new one and reinstalled into the refrigerator body.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathy from TEMECULA, CA
- Parts Used:
- W11384469
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Light switch broke off
We looked up the problem online with the model number of the refrigerator. We ordered the part and followed the video installation that was sent with the order and was found online prior to purchasing
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from Aberdeen, SD
- Parts Used:
- 4386917
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
One of the door shelf end caps broke
I removed the broken end cap and then I snapped the metal shelf onto both end caps and replaced the shelf.
I really must say that dealing with PartSelect was exceptional. It took about three days for me to get the part and, prior to that, it was very easy for this sidewalk fixer to locate the correct part on their website. Thank you for your excellent service.
I really must say that dealing with PartSelect was exceptional. It took about three days for me to get the part and, prior to that, it was very easy for this sidewalk fixer to locate the correct part on their website. Thank you for your excellent service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from Clinton, MA
- Parts Used:
- 2174134
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The crisper cover was broken.
Took the old out and put the new in - sits on mounts in refrig. Took old gasket out (still good) and put it in the new bracket.
The trick was finding the SSN to purchase the right part (failed on first two orders). The SSN was located in the freezer NOT in the refrig where the instructions said it was. Freezer is a bottom freezer making it difficult to see.
The trick was finding the SSN to purchase the right part (failed on first two orders). The SSN was located in the freezer NOT in the refrig where the instructions said it was. Freezer is a bottom freezer making it difficult to see.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from Greensboro, NC
- Parts Used:
- WP2196157
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Old tube had cracked due to being frozen....
I followed the simple steps outlines in the great video! Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Suwanee, AL
- Parts Used:
- WP2155476
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
clips broken on both sides of kick plate.
alined the new part and snapped it on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gregory from Virginia Beach, VA
- Parts Used:
- WP2155013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Socket set, Wrench (Adjustable)
Dryer made loud intermittant humming sound after 20-30 minutes of use
Unplug Dryer. Remove 2 5/16in hex screws from lower panel and remove panel.Remove 3 5/16in hex screws attaching lint duct. Remove 8 1/4in hex screws attaching blower housing. Remove 2 1/4 hex screws attaching thermostat to blower housing. Using adj. wrench on back of motor shaft nut to hold, loosen fan assy. w/ 7/8in socket. Remove 3 5/16in hex screws holding fan housing to motor mount. Remove 2 5/16in hex screws holding housing and motor mount to base floor. Push belt pulley wheel up enough to loosen belt and take off rear motor pulley. Motor w/mount can be slid out bottom for replacement [wires are layed toward front].Using 6in flat tip screw driver press down to unlock front & back motor bushing holddown clamps. Pinch electrical wire connector ends to pull off old motor. Remove and Install new motor, reversing steps. Belt replacement [suggested w/new motor] requires removal of 2 5/16in screws to lift/remove door w/front panel [disconnect door switch wires upper right rear corner].Remove 4 5/16 screws holding front bulkhead. Once bulkhead is pulled up and off, allow front end of drum to sag and rest IN PLACE [removal not required to slip old belt off and install new belt]. Note belt location point around drum. Slide new belt on. Reinstall bulkhead and panel/door [Don't forget door swich wires]. Adjust belt into position and push spring-held belt pully up to allow looping of new belt around rear motor belt pulley. Complete w/hand turning of drum to ensure belt is aligned and feeding properly. Reinstall lower fan housing/covers/thermostat,etc removed for motor installation.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cecelia from Beaver Dam, WI
- Parts Used:
- W11384469
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
light staying on
A very cold and brittle switch in a 17 year old fridge. Used screwdrivers to pry out with some resistance Had to cut the molded plug in half and split wires, because replacement contacts were farther apart than the original. End result, works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fred from Watertown, NY
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
19 year old light switch broke
Great service. Unpluged old switch and pluged in new one. Works great
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- STANLEY from OAKLAND, NJ
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
rocker switch broke off
disconnected el. power to fridge. pried out broken switch with small screwdriner and pulled out w/water pump pliers. installed new switch and pressed into opening.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Jefferson Hills, PA
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Internal light did not come on each time the door was opened.
After disconnecting the electricity. I followed the instructions as indicated in the "HOW TO" article on the website. I used a steel putty knife and pried the light switch out of its retaining hole. I worked the right side the most since this is the side with the retaining clip. After I removed the switch I transferred the two electrical outlets to the new switch and easily snapped it into place. Engaged the electric power and tested the switch.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- uri from riverhead, NY
- Parts Used:
- WP2196157
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
thread broke
Unscrew broken piece, pull it out and then insert new one, security it in place and connect water line again, make sure It's thight check for leaks and done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- LARRY from PARKER, AZ
- Parts Used:
- WP2196157
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Filler Tube Broken At Elbow Where Line Hooks Up To
Replaced fill tube
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Copperas Cove, TX
- Parts Used:
- 4386917
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
plastic end cap clip broke
removed retaining bar removed and replaced end cap and reinstalled retaining bar.
Was this instruction helpful to you?
Thank you for voting!