ED20DFXEB00 Whirlpool Refrigerator - Instructions

This is an incredibly easy repair.

1) Remove the three screws holding the old icemaker

2) Disconnect the electrical connection (I used a spoon to get in and undo the connector clip

Do the opposite to install the new icemaker.

Total elapsed time was about 5 minutes.

Removed the 2 screws holding the light bulb shield, then the 4 uolding the metal panel. Unplugged the olw door switch and replaced.
reassembled the pieces.

After taking apart the ice maker, the only obvious replacement was the motor assembly. I check various Internet sites and found the best price at PartSelect.

I removed the ice maker from the freezer after turning off the ice make switch. Removal was easy with only one screw holding in the entire assembly. The ice maker has rails that allow it to slide in and out like a drawer.

After R/R the motor assembly and returning the ice make to the freezer all that remiand was to see if it worked.

Within 10 minutes I had the wonderful sound of water filling the ice maker tray. Within 30 minutes of that, ICE!!!

Shopping, ordering and shipping of the part was fast and efficient. I'll go with PartSelect for all my future appliance needs.

It was not complicated but it took more squeezing and reaching into the narrow space than actually removing three screws and unplugging the electrical harness. But that was all that was necessary, to install, three screws held the unit in place and re-connect the electrical harness. It saved me about $100 in labor and the inconvenience of scheduling a service call and waiting for a week or so. The best part was that I ordered the unit on line on Tuesday eveining and it was at my home by Friday afternoon with no extra shipping charges. Great service!.

First took all frozen food out and than undid the screws that held back on--than cut the wires that held the piece and replaced it but also found that the plug was frozen so we thawed that out, that is why it took longer. Used air compressor to blow air and it broke it free and than we finished and put the food back after it got cold. So far it is working find and to beat all we received our part the next day so my husband could fix it that weekend--Thank you for the quick respond-
Patricia in Marengo Ohio

Shut off the water supply at the wall then using a 1/4" nut driver I removed the steel and cardboard backing plates from the rear of the refrigerator. Disconnect the main water supply hose and then the two water lines for the chilled water dispenser and ice maker. Remove the two screws on a support bracket which holds the valve in place.
Reassembly in reverse order.
The process was very easy and took no longer than 15 minutes and works just like new. This is a good time to do some thorough cleaning around the fan and coils to keep them working properly as well.

take out Ice maker tray, remove three screws holding the ice maker, unplug electrical connector. Replace with new Ice maker,Ice started to fill the tray. ENJOY!!
THANKS.

Tried to repair existing valve which I have succesfully done many times by cleaning and removing grit from internal neoprene parts until new parts received. Was not successful. New valve worked perfectly. this is only 2nd repair needed on this ref. since new. 1st was defrost timer. Ice maker hasn't missed a lick since new.

First I turned the water off behind the refrigerator....took the ice maker inlet valve off, put on the new one. As simple as that & it is working beautifully....not only am I a woman but 55 yrs. young too!
With the right part & right tools NOTHING is impossible & I saved myself a repair persons fee!!!

pulled cover off back of refrigerater at the water line,shut water off removed water line,check for pressure at the line by puting the line into a 5 gallon bucket it was ok.took the dispencer lines off that goes up to dispencer,hit dispencer switch could hear buzzing at the dispencer unit but no pressure.so i replace water inlet valve

Reassembled auger assembly to new ice bucket with new screws. Fairly simple and straight forward.

Took the old one out and plug the new one in, simply as 1 2 3. Order the part one morning,it was here the next afternoon, the ice maker was fixed in less than a half hour. we will order from you the next time.

Super easy - emptied door of all food, unscrewed bracket from top of door, lifted door off and set aside. Broken cam removed, new one screwed in, and lubed with some Vaseline. Set door back in new cam, screwed bracket into the top, and good to go. I was kinda worried about shopping from PartSelect since I had never heard about them, but the part was here in less than 2 days. Pretty awesome little company.

Very easy to order from parts select. Took seconds to replace.

I determined that the ice cube maker was no longer heating the cubes so they could be released into the ice tray. After ordering a new unit, taking out four screws and disconnecting the quick disconnect of wires I plugged the new one in and we were back in business.