ET20TKXDN01 Whirlpool Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Thomas from Roseville, CA
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door light switch disintegrated
Very simple fix, remove 3 screws, two connectors to the old switch
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from Neptune, NJ
- Parts Used:
- 819342
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Could not properly open the door wirhout the handle
I Clean the handle both top and bottom. I place the cap in place on the bottom of the handle and tap it in snug with a hammer. I then place the top of the handle back into it's original position and then I screwed the end cap in place at the bottom. EASY !!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from FERN BCH, FL
- Parts Used:
- WP2218118
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Broken butter door
I popped the new one right in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from ROCK ISLAND, IL
- Parts Used:
- WP2314549
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
My crisper cover frame broke
It was very easy just took out the old broken crisper cover frame out and put in the new one. Simple as that.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- stu from richmond, VA
- Parts Used:
- W11384469
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
fridge door switch did not work
I removed the switch housing (4 screws), replacing the switch in the housing was a snap. It took 5 minutes, cost $8 and light works like new!
Why didn't I order this part and do the repair earlier? Very simple.
Why didn't I order this part and do the repair earlier? Very simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jon from Brea, CA
- Parts Used:
- 819342
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Refrigeration Door Handle End Cap cracked
The repair was REALLY SIMPLE. I popped off the cap cover from the existing end cap, insert the door handle to the new end cap, screw on the new end cap with a Phillips screw driver, and then push the old cap cover back on. Took less than 10 minutes, if that.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Oliver from Madison, AL
- Parts Used:
- 4387535
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Cimpressor would not start
Checked compressor with amp meter, and found it was not running, found Overload Switch bad.
When removing old switch watch carefully which lug you move wires from, so you will know which
lug to put the new switch on.
BE SURE YOU KNOW SOMETHING ABOUT
ELECTRICITY!!
When removing old switch watch carefully which lug you move wires from, so you will know which
lug to put the new switch on.
BE SURE YOU KNOW SOMETHING ABOUT
ELECTRICITY!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- dorotea from staten island, NY
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Light didnt go on
The light rocker switch wasnt working. I found the part on the web site. It was so easy. I used a screw driver to pop out the old one and pop the new one in. It took 5 min. Thanks!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from BUFFALO, NY
- Parts Used:
- WP2218132K
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Replace meat draw
Came on time, just slide in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ROGER from GREER, SC
- Parts Used:
- WP2314549
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken crisper frame
Replaced frame
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christine from WASHINGTON, DC
- Parts Used:
- 819342
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
End cap of fridge door had failed
Simple to unscrew and replace parts
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeff from WINSTON SALEM, NC
- Parts Used:
- WP2176225
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The handle broke and my wife was afraid to close the door because she might not be able to open it back.
The part-select video showed me to do the following:
Unplug dish washer
Open the door and unscrew the screws around the inside of the door all around.
Place the screws in the detergent holder with a cap until finished.
The door mechanism is at the top and attached to two electrical wires.
Unfasten the wires from the attachment.
Take the new attachment and fasten the wires to it.
Place the attachment back in the spot and make sure handle is sticking thru the hole to the outside.
Reattach the screws.
Plug back chord.
Finished - 15 minutes
Unplug dish washer
Open the door and unscrew the screws around the inside of the door all around.
Place the screws in the detergent holder with a cap until finished.
The door mechanism is at the top and attached to two electrical wires.
Unfasten the wires from the attachment.
Take the new attachment and fasten the wires to it.
Place the attachment back in the spot and make sure handle is sticking thru the hole to the outside.
Reattach the screws.
Plug back chord.
Finished - 15 minutes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- duncan from HOWELL, NJ
- Parts Used:
- 2159061
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
After 17 years, the old door gasket was split and showing signs of mold
The gasket has an inner lip that fits over the edge of the door plastic liner. The old gasket was removed by pulling it straight out, in the plane of the door. Try not to pull sideways as it could crack the door liner, which gets brittle with age. The new liner had a brown magnetic strip, which holds the door closed, and this fits behind the edge of the door liner. Start on the bottom of the door. A helper is useful to hold the gasket loosely vertical. A flat blade screwdriver can be used to pry away the liner to insert the new seal. Once you have worked in the lower edge, install both sides, and then the top. Some juggling side-to-side may be needed for an exact fit
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ted C from DSRT HOT SPGS, CA
- Parts Used:
- WP4387503
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Drain clogging causing water to leak bottom of fridge
After watching videos how to replace went very easy.removed ice maker cut wires replaced switch put back together now working ok so far.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from HOUSTON, TX
- Parts Used:
- 4387478
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Faulty light socket
Followed the video instructions.
Was this instruction helpful to you?
Thank you for voting!