GX5FHTXTT00 Whirlpool Refrigerator - Instructions

Took the new door seal out of the box, layed it out as straight as possible heated it with hair dryer 4 1hour took the old 1 out by hand and replaced it with new one no tools needed 10 min job

The old icemaker had a bad motor and would stall in the fill cycle causing my kitchen to flood on occasion.

The new one was so quiet, I thought it didn't work!

Anyway, one nutdriver and 5 minutes and I had the new one in there... It is so quiet, and I always have plenty of ice now!!!

Thanks!!!

well, first, after calming down i removed the glass from my sink (this took a half hour). then i went to the computer and looked for jenn-air parts. the part-select site came up. the site was very easy to use and although i usually leave things like this for my husband to do i decided to order the part myself, which i did.
the trick was finding something on hand to cover the tops of the crispers which were both full of vegetables. i innovated and used a shallow broiler pan and its lid which covered 90% of both the crispers. the part came in five days unwrapping the part was easy, cleaned it with windex (no sink soaking this time) and inserted it on top of crispers............totally easy!!!!!

tested bulb good ,replaced door switch first(least expensive)then ordered light socket and circuitboard.If clicking sound is heard replace circuitboard first to save on return shipping because the switch and socket where ok

Gain access to rear of refrigerator. Use protective board to prevent marring floor. Unplug refrigerator. Turn off water supply and depressurize line. Remove old water filter head. Disconnect filter head inlet water supply line located behind the refrigerator. Disconnect the filter head filtered water return line at the water valve. From refrigerator interior, disconnect the lower filter water cover. Press the outer cover away from filter head until one end is free of the water filter head tang and remove cover from second tang. Push the Styrofoam "block fill" toward the rear of the refrigerator to remove it. If you try to remove this from the outside by pulling it, it will likely break. Pull water filter head assembly to remove it. Install new part by reversing the steps.

Snapped new cover on.

I just had to exchange the bucket, right part the first time.

4-Screws 3 plactic hoses to remove pull 3 tubes out and instol new part last then 15 min. Making shure is no leaks. Easy

Wife learned you can overload the cheese and fresh veggie trays and the plastic rails broke. Repair required removing parts from the old crisper frame -- no experience and no instructions. Had to study broken part and figure out how to remove parts. Released catches with a knife and, by trial and error, figured out how to install rescued components on new crisper frame with minor damage and frustration.

I called the local Amana repair man, wanted $150 for a new ice maker because they could not get the part I needed. Found Partsselect.com and the part cost $17 with shipping. They saved me over $100. The repair was very easy too, just removed a couple of screws.

Thanks,
Matt

Removed drawers and glass top and support bars Two screws on slid bar two screws on end cap, Make sure you take time to remove air control it has two pivot points with small taps.
Then just replace parts as you had taken off very easy.

lift glass, slide new rail in replace glass. 2 min repair.

Removed the crisper drawers (pull out, then up & out), remove the glass shelf above the "pantry", remove the pantry door (easy because hinge stud was broken), then remove the pantry drawer. Use 1/4" nut driver to remove the broken LH End Cap...it pulls up and out. With the phillips screwdriver, remove/replace the steel rail for the drawer action to the new part. Replace in reverse order (after your neat freak SO cleans everything!).

noticed the fridge and frezzer were not cold one day.i got on google and typed in the problem and found out the the relay goes bad rather often. was an easy fix. found the parts here on partselect and recieved in with in 2 days of ordering. pulled the old part out put new part in and plugged fridge in and was back up and running with in minutes..thank you partselect....

I loosened the two top screws, removed the bottom screw, lifted up on ice maker and slid it off, unplugged the wire from refrig. I transfered the wire to the new icemaker, pluged it back in, placed it on the two screws, installed lower screw, tighten top screws. Total time spent less than 15 minutes. The ice maker cost $125.00 with freight. Sears wanted $374.00