3EHD261MMWR1 Whirlpool Refrigerator - Instructions

Removed the one screw that holds the dispenser arm on one side and was able to remove the entire assembly. Had to remove the water tube from its holder. Very easy only two philips head screws hold it in place. Fitted the new arm in place while positioning the water tube in the space above the dispener arm. replaced the first screw removed that holds the dispenser assembly in place. Reattached water tube. Repair complete and working better than new!

Removed the top hinge cap. Removed the 3 screws with a nutdriver. Lifted the door off of the bottom hinge and placed it on it's side. Then I removed both closing cams (one screw holding each). Clean the area then replaced each cam. I put some vaseline on the bottom cam and replaced the door. 4-5 minutes not counting removing and replacing the food inside the door shelves. I'm 56 years old and have always done most of my own handywork. I don't remember any job going so smooth and fast! Ever!

(1) Ordered PS371704 from PartSelect! Best advice EVER! (2) Unplugged refrigerator (since the water solenoid on the back of the refrigerator is powered to switch ON the water, you NEVER have to turn off the water!) (3) Pull off the refrigerator's bottom grill. (4) With a small saucer under the fittings, unscrew the black and white tube fitting. There is only one nut to remove on the white tubing side. You'll need to undo the compression fitting on the black tubing and slide off the compression nut. You'll need to MAKE SURE you keep these nuts and replace onto the black and white tubing the SAME WAY you took them off. You'll NOT need to use nut drivers as finger tight is the key. Too hard and you'll ruin these plastic nuts. You should get only about 1/8 cup or less of water during this whole exercise. (5) Cut off the old, broken water nozzle. (4) Find a screw of the appropriate size to fit tightly 1/2 way inside the new tubing (this is to ensure your old and new tubing are connected to feed through the door). If screw is not tight within the tubing, wrap part of a plastic (thin) sack around this screw a couple of times and force into the tubing. You'll, of course, then need to use the hacksaw to cut the head off the screw as you'll be forcing the other half of the screw into the old cut tubing (6) Chase the dog out of the kitchen and cajole your wife (significant other) to push the newly joined tubes through the top of the dispenser, through the door and out the bottom as you will be gently PULLING on this old tubing from the bottom until the new tubing pops through the doors bottom. (7) Once this new tubing is out, you will separate the old tubing and, using the nuts in the proper sequence, connect this new tubing to the white tubing. (8) Plug the refrigerator back in and test flow the water. Check to ensure the plastic nuts have no leakage ... button up the bottom grill ... and enjoy the fresh water! PS> Don't forget to praise the wife (significant other) and give the dog a treat for staying out of your face!!

1. removed old broken arm (w/screwdriver)

2. .....gently placed 'new part' in place (of old)
and one (& only one screw), tightened
slightly.....and presto.....
PRESSED ON NEW ARM.....
..............'WATER FLOWED'..... THANKYOU,
JIM

Remove top henge, lift door off bottom henge, take off old plastic closer put on new one. Door works great now

One screw hold the dispenser guide in place with the 1119056 Stop. I would recommend buying a new Stop as unknown to me mine was cracked. Check the condition of the stop before ordering just the guide. I had to order a new stop from Sears. Very simple to replace both the guide and stop.

I took the front access panel off by unscrewing the 2 philips screws under the water dispenser tray. The plastic trim piece lifts straight up. The assembly that holds the electronics to operate the ice dispenser and water dispenser is held to the door by two 1/4 hex head screws. You pull that up and out of the way. Then take the metal bracket off that holds the water nozzle to the door. There is a black water supply line that runs down the door and out the hole in the center of the left bottom hinge. (You’ll have to pull off the kick plate at the bottom of the refrigerator to access the connection) It is connected to a compression fitting that attaches to a larger white water supply that runs through the inside of the refrigerator. Feed the new black supply line down through the door (up top) and fish it through until it stops. It most likely will not poke through the hole in the hinge. I took a scratch awl to center the new hose to enable it to poke through the hole in the hinge. Reconnect the compression fitting, put the kick plate back in place, put the electronics back in place as well as the plastic trim piece that goes around the dispenser itself. Sit back, enjoy a glass or water and pat yourself on the back for saving yourself a $100 service call.

Follow simple instructions found on youtube

I tipped the refrigerator back and my friend used an adjustable wrench to attach put the new wheel assembies on. I also used a socket wrench to get the old attacheement bolts to thread. I rolled the cleaned appliance in place and adjusted the wheels with the socket set for easy door closing. It went smoothly.

I followed your on line video, that was a fantastic help. Easy as 1,2,3. I used the tools he recommended and followed his steps. I replaced the cam on the door and on the bottom pin, its works like new.

repair was easy. watch the video

Removed all the adjustable shelves inside the door. Removed the top hinge cover (1 nut). then the top hinge bracket (3 nuts). The door doesn't weight very much so you shouldn't have to worry about the door just falling off after you remove the top hinge. then simply lift the door off the bottom hinge and carefully lay it down. One nut in each of the plastc cams on the bottom of the door and an easy swap out with the new parts. A little vaseline one at least one of the surfaces of the cam, reverse the order and simply put things back together and your good to go. Door closes on its own like new. You might as well get both parts for the lower cam and swap them out simultaniously since you have the door off. PLEAS NOTE: Yes there are two different parts for this repair.

bulbs were not burnt out. received the new switch in a few days. watch the short video, was good to see how it comes out. used a putty knife to release the defective switch, removed wires put them on the new one and posed the new switch back in. Not bad Part cost $11.00 7 dollars shipping so for 17 bucks it works great. nice to see what is inside the refer!

Removed the two screws holding the funnel in place...removed the old one and replaced it witht he new tubing...screwed screws back in and the jov was complete. It actually took longer to get it out of the sack than it did to put it together

I unscrewed the fill tube screws from the back of the fridge, and pulled the tube out.

Then I put the new tube in, screwed the screws back in and reconnected the waterline.