WRS325SDHW11 Whirlpool Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Billy from Garland, TX
- Parts Used:
- 4388736
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
ice drum broken
I removed the ice bucket and dumped the ice (saving part of it to put back into the bucket after repair).Using the nut driver,removed all screws,rmoved the auger that the broken drum is mounted on.I reoved the nut on the end of the auger(with my pliers).Slid out auger removed broken drum,replaced new drum and re assembled using your easy to follow instructinns.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jack from Topsail Beach, NC
- Parts Used:
- W11396033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken refrigerator compartment light switch.
The best part of the repair was how easy it was to find and order the part. Instead of searching the parts houses around town I just went to the PartSelect web site, quickly found and ordered the part in about five minutes, received the part the next day at my home and was ready to make the repair. Wow! What a pleasure for something to work the way it was meant to. Removed old switch located by prying out with sharp knife or screwdriver. Don't worry about breaking it or cracking plastic. Disconnect(unplug) wires from back of switch. Replace (plug-in) wires on back of new switch. Insert in location of old switch. Finisheed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harold from Lindenhurst, IL
- Parts Used:
- W11396033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
icemaker
installed new parts
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- catherine from LEEDS, AL
- Parts Used:
- 4388736
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
ice would not chrush or come out into glass
removed 9 screws, removed all parts, laying them in order, so they would be easy to replace.
reassembled in order I had removed them placing the new auger drum in place of broken one.
replaced ice container in freezer, poured in a few ice cubes them crushed them.
reassembled in order I had removed them placing the new auger drum in place of broken one.
replaced ice container in freezer, poured in a few ice cubes them crushed them.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- al from alamogordo, NM
- Parts Used:
- 4388736
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
the ice maker stopped delivering ice, crushed or cubed.
removed six screws removing the cover and exposing the shaft & auger.
I then had to remove the snap ring & undid the end nut that has left handed threads.removed the 6 auger plates and then replaced all parts in reverse order of their removal.
I then had to remove the snap ring & undid the end nut that has left handed threads.removed the 6 auger plates and then replaced all parts in reverse order of their removal.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Lantana, FL
- Parts Used:
- 4388736
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Broken vanes in ice bin auger
Ordered part, watched video. Had a problem with reassembly of ice crushing assembly, did a re-do as one of the blades had dislodged from the drive shaft!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from New Braunfels, TX
- Parts Used:
- 4388736
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
The auger drum had broken & not distributing ice.
Once I removed the ice bin from the freezer section of refrigerator and removed all the necessary screws was able to remove the auger drum, but had some difficulty in reinstalling the crusher blades in the dispenser. After several tries, got it right and dispenser is performing like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Smyrna, GA
- Parts Used:
- W11396033
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Frost in bottom freezer, freezer 8%, ice maker works
replaced electric control board, defrost for six hours. next day (24 hours) same problem, [email protected]
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Albert from Fort Mill, SC
- Parts Used:
- 4388736
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Ice Bin Auger Drum cracked.
It was a breeze to remove and replace. Made even easier by the previous DIY guys posts. Make sure you turn the nut at the end of the shaft clockwise to loosen. Taking a picture of the blades for ice crushing before removal for future reference is a great idea. It wasn't hard at all. Just take your time.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cecelia from Beaver Dam, WI
- Parts Used:
- W11384469
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
light staying on
A very cold and brittle switch in a 17 year old fridge. Used screwdrivers to pry out with some resistance Had to cut the molded plug in half and split wires, because replacement contacts were farther apart than the original. End result, works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rick from Florence, SC
- Parts Used:
- 4388736
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
The auger drum broke from the shaft
I removed the 4 screws holding the front cover in place. Removed the 4 screws holding the ice auger cover in place. Removed the c clip holding the auger on the shaft. Pulled out the auger shaft. Removed the broken auger drum and replaced with the new one. Reassembled in reverse order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- debbie from Shepherdsville, KY
- Parts Used:
- 4388736
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
would not dispense Ice
Took the Ice Bin Out emptyed it then removed the nesasary screws pulled the broken Peice off and sliped
the new part on held the metal peices together so we would know how to keep them in order for fear of putting them in wrong place but we did it now it works great thank you so much for getting the part to me so quickly your great.
the new part on held the metal peices together so we would know how to keep them in order for fear of putting them in wrong place but we did it now it works great thank you so much for getting the part to me so quickly your great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anthony from San Ramon, CA
- Parts Used:
- 4388736
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Ice not dispensing
This was not a hard repair. Just remove all the screws and slide out the old Auger drum. It is always good to take a picture first incase you have any problems putting it back together. Be careful to put the ice crushers back in the same order and make sure you look at how the "door spring" connects before pulling it apart.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- B G from lindale, GA
- Parts Used:
- 4388736
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
no ice dispensing
removed ice storage drawer, removed dispensing shaft from storage drawer, replaced plastic auger and reassembled.
quick and easy....
quick and easy....
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Austin, AR
- Parts Used:
- 4388736
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Ice maker dispenses plastic parts (the auger)
I began by removing the ice maker and storing the ice. The part did not come with instructions so I began taking the ice maker apart. I ran into problems rather quickly so I went to the "part select" web site and there was a video with instructions on removal and reinstallation of the auger. It was a breeze after that. These guys are obviously professionals!
Was this instruction helpful to you?
Thank you for voting!