WRS325SDHW11 Whirlpool Refrigerator - Instructions

Removed the access panel on back of unit located the Run Capacitor on the compressor and removed the bad one and put the new one on and pugged refrigerator back in and it started up and works fine now

The switch fix but did not fix the problem. I assumed the wires go on the same way as on the old switch. Is it possible if one light Burns out, the other will not work either?

Used the suggested problem list here to narrow down that the repair was most likely the run capacitor. Poped the new one in and I now have better control of my compartment ranges. I have a temperature gauge in each compartment. Check them every opening of the doors.

replaced the drum ---- however it would of been more helpful if directions came with the part on how to take off the old drum we had to look on line to see how to do that wants we got that done the rest was a piece of cake

We looked up the problem online with the model number of the refrigerator. We ordered the part and followed the video installation that was sent with the order and was found online prior to purchasing

Repair was tremendously easy. All I did was remove old light switch by prying out with screw driver and plugging in the new light switch and pushing it into the hole. Simple! The instructions weren't needed, but they were very thorough.

Pried out the old switch and installed the new switch.

Replacement part arrived via FedEx package with one hinge already broken off, unable to install. Still waiting on requested replacement.

Opening up the Evaporator Fan section was a quick and easy job. After opening, I checked and removed the fan and looked at the grommet. The grommet on the fan was tight and secure and I could no longer hear the noise. I closed the opening. Something I had done while checking the fan grommet must have solved the problem. I have not hear the noise again!

Eased the putty knife under the edge of the switch housing and pried it off. Pulled two wires off the old terminals and hooked them onto the new one and reinstalled into the refrigerator body.

Had to push the light switch to get lamp to light up.
Removed power from refrig. and removed old light switch
and replaced with the one I got from Partselect. Turned power back on and was done.

Remove 4 self tap screws holding on front cover/bin handle. Remove 2 self tap screws holding drum cover. Remove 1 self tap screw at back of bin holding door actuating rod and spring, slide forward to disengage. Remove "E" clip and flat washer. Remove plastic nut {clockwise/left hand threads]and remove crusher parts [keep in order removed]. Slide new drum on shaft and reassemble crusher in reverse order. Install drum cover w/2 self tap screws. Install flat washer and "E" clip. Re install actuator rod and spring assy. Install front cover and test in refrigerator. The 2 self tap screws that hold drum cover are easier to remove with a 1/4' drive ratchet and 1/4" socket because of limited space behind actuator rod. This job is a snap to do. I'm sure it's at least $50.00 cheaper than a service call.

bulbs were not burnt out. received the new switch in a few days. watch the short video, was good to see how it comes out. used a putty knife to release the defective switch, removed wires put them on the new one and posed the new switch back in. Not bad Part cost $11.00 7 dollars shipping so for 17 bucks it works great. nice to see what is inside the refer!

I took the white slim pipes off the brackets. Put the white pipe in the hole in the freezer and push the glass into the brackets. Repeat again..

At first I went to a local part supplier and they didn't have it in stock but could order it for me for $55.00 plus $10.00 to ship it. I told them I would have to think about it. I went home and got on the computer and found your web site and was I shocked when I saw the same part listed for $6.98 and $7.00 to ship it. You guys saved me $50.00. The part arrived in two day and took 5 min. to install. I now have light in my refrigerator. Thank you.