WRFF3036RB00 Whirlpool Refrigerator - Instructions

I noticed that the refrigerator was having trouble maintaining temperature. Thought it might be time for new one until I found out that a new frig was $5k to $7K. Just happened to notice that the light switch didn't look quite right (was not sitting sqaure to the door). Once I pressed it it came loose. I then realized the the lights were staying on (50 watts of heating). Replaced the switch and the frig started working like new.

Unplug appliance. Socket wrench to unscrew two screws. Module drops down. disconnected two press-on wires by prying off with screwdriver. Removed old switch. Press-fit new switch. Reconnected two wires (color coded). Screwed module back in place. Plug in appliance.

Took it out of the box and just snapped it in place.

Poped ou the old switch, connected new switch and pushed back into socket.

I used a knife blade to slip under the edge of old switch to pray it out of the hole it was inserted into, switched the wires and replaced the new switch into the same hole. It took about five minutes!

replaced electric control board, defrost for six hours. next day (24 hours) same problem, dusterhoff2928@charter.net

Used screw driver to pop out old switch. Used pliers to hold wire connection from fall back into slot on fridge. Inserted new swith into plug and pressed new switch back in place.

Popped the old one out with a kitchen knife and popped the new one back in. It tool less than 15 seconds!!

My owners manual said to unplug fridge from elec outlet, use a kitchen knife to gently pry off the switch plate
(manual had a pictoral example), unclip the two wire, replace with on new switch and replace the switch. Close
door and plug back in. Open door to check that the lite
works. Walla! It did. Thanks!

Sincerely, Ron Marshall, Billings, MT

I pried the old one out with a screw driver and pushed the new one in. I expected instructions in the box it came in but there were none.

This is definitely one of the easiest, most rewarding projects I've ever done! From the point of easy ordering to receipt of the part in just two days (!!!!), opening the box was probably more effort than clipping the part in place! I'm keeping partselect on my favorites list!

Please bear in mind I am 65 years old & it was harder to get up & down off the floor then to change the switch. Was very easy - watched video, unplugged unit. I used the putty knife at the right front corner to work loose, when it came loose had to loose the left side a little. The unit pulled out easily. detached the wired that had a single plug with 2 prongs on it. Attached the plug, pushed new switch into place. There was no way you could place wires on wrong prong. When done, plugged refrigerator back in & checked if working. I CAN SEE THE LIGHT and the food in the freezer now. Thank you for making an easy repair.

I had several times tried to get the old switch out but with no success. Ordered the "repair kit" and followed directions for removing old switch (there is a plastic spring clip on one side). Easy to unplug the old switch, plug the leads into the new one, snap the new one into place. Took about 5 minutes total--piece of cake. I wish I'd thought to try this years ago when the old switch began to fail.

I have never before seen a bulb with the filament intact not light. If the bulb's filament seems intact, screw the bulb into a known working lamp and see if it lights. When screwing it back into the socket in the fridge, it takes a bit of extra effort to fully seat (until it does, it won't light!). For replacing the switch, I unplugged the unit, used a paint scraper and worked it under the switch bezel from the right side. A bit of moxie, and the switch came out. The replacement switch had a different spade contact spacing than the original. I used a pair of scissors to cut the rubber bridge between the two switch wire connectors so I could connect to the new switch. In the end, it turned out to be the bulb. NOTE: The Model TC18KL is _not_ listed! What I finally found that the number "P7803211WL" on the sticker is actually a manufacturing code. Found this out by searching, and Sears' part search came up with matches.

Simply stick a putty knife between the switch and refrig wall. Pop out old swith, remove both wires by pulling off switch by terminals. Throw switch out. Put wires on new switch and push into slot and all done. Nothing to it! Took me 5 minutes if th