6ET18ZKXAN01 Whirlpool Refrigerator - Instructions

Replaced bracket-amazed to find how quickly I was able to id the part on this 20 year old refrigerator. Ordered the part and received it the next day! Thanks for the good service! , Bob

Water was already off. All I had to do was pull the fridge away from the wall, remove two screws that hold the fill tube onto the back of the frige, then remove the fill tube. Install the new fill tube, reinstall the two screws. Had to cut the water line straight and clean, slip on the new Compression nut and farrell and insert into the new fill tube, tighten-up, good-to-go.

After I did the prep work of removing the items inside the door the project took less than 15 minutes to get the repair job done. 1. Remove the door by taking off the top hinge cover on top of the door, remove the three screws with a socket wrench, remove the plastic gasket under the hinge, left door up and off the lower hinge pin 2. Place the new bracket on the freezer door hinge pin, flange side down 3. I had to place an extra spacer washer, which I had on hand, on top of the hinge bracket 4. Replace the door on the bottom hinge pin 5. My husband held the door in place as I reattached the top of the door with the plastic spacer and 3 screws I had removed 6. Replaced the plastic gasket and hinge cap on the top 7. With the door reattached, I removed the existing screw under the door directly below the new hinge bracket, lined up the hinge bracket to the screw hole and attached it in place. Much to my surprise and pleasure, the door swings perfectly, stopping where it should with the door shelves loaded! Thank you PartSelect for having a part that would work for my 16 year old refrigerator even though I had to add a washer shim to make the new part as thick as the original.

Simple. snap together instalation, no tools required. Thank you partselect for having the parts pictured with a size grid in the background, without that size grid, it would have been more difficult to select the right part. And, may I add, "my local appliance repair person indicated- he could not locate a repair part." I found the part via google search, and partselect.

This repair was super easy. there are only 5 screws to remove to get at the defective switch. 3 in the housing where the light bulbs are and 2 in the front trim piece where the cooling adjustment dials are. I never did unplug the fridge ,but probably should have although nothing bad happened. I removed all 5 screws using a 1/4" socket ( a nutdriver would work well also). there is also a small dia rod that comes down from the coolness adj. wheel that when you re-assemble goes though the middle of the wheel. The switch has only 2 wires that clip on with the push on flat type connectors. Very simple. I removed the wires and then the switch can be removed( it is only held in by 2 squeezable side clips). I put the new switch in and connected the wires , checked to see that the lights went on and off. which they did. then just put the screws back in.....done. also I would like to say that when I ordered my switch it came super fast. I ordered it online at 11:00am on a tuesday and it was on my doorstep in wisconsin by 10:00 am the next day...Thanks

Removed screws from the back of the part in the fridge. Pulled old part out. Measured the old part. Cut new part to fit. Replaced new part and tightened the screws. Worked perfectly.

Took socket out and replace it with new one. Very easy. W saved alot of money doing it ourself.

First, although I was SURE I knew what to do, I watched the repair video. I used needle nose pliers to push broken support into wall since I could not pull it out. Selected correct wall fixture, spread holder pins, and snapped into wall opening. Couldn't have been easier!!! Very useful site.

R/R part, 3 screws reconnect 3 wires. easy.

Ordered new replacement parts. Took new parts to the work site and proceeded to install them. First removing the reminance of the old clips from the bar its self. Using a flat screw driver pri the metal tabs open so the old part can be removed. Reset the crimp in the metal bar and install the new clip into the ends of the metal bar. Insert the new clips into the appropiate holes in the door liner and pop into place. Very easy repair when you have the right parts.

On the left side I unscrewed the screw and replace it with a new one . The right side in had to take s file and file of the rivet. You can use a rivet gun or a metal screw to replaced the clip. Once it is finish open the refrigerator door to see how to line the kick plate into the clip. A piece of cake.

Snapped in new end caps and attahed existing shelf bar. Have done this twice. We tend to stuff too many items on that bottom shelf.

Removed correct part from those provided and slipped it into position. No tools necessary.

Followed the instructions on package, went extremely well, with no problems what so ever! Thanks so much for the part and how to do list!

Very easy to replace. Disconnect water line. remove 2 screws pull out filler tube. replace with new one.