JUCFP242HX00 Whirlpool Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Keith from Metairie, LA
- Parts Used:
- 4317943
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Old ice maker was leaking water during initial fill cycle
Removed three srews holding the ice maker in place. Unplugged the wiring. Plugged in new ice maker wiring. Installed the new ice maker with the three screws. I left the old wiring in place. Works perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RONALD from SHREWSBURY, MA
- Parts Used:
- 4317943
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Icemaker stopped working
Easy removel: remove one screw and loosen two others; unplug connector; swap actuator bar; replace
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lev from Fanwood, NJ
- Parts Used:
- 4317943
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Plastic coating chiping-off
First I removed one screw that hold the element in place, lifted element about half an inch. I then pulled the element out about 2-3 inches and disconnected the wire. Then replaced two clips on top of element and re-connected the wire, put screw back and VUALYA....done!!!!!!!!!!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeremy from Pittsburgh, PA
- Parts Used:
- 4317943
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
icemaker didn't work right.
Unbelievable experience. Ordered on Friday received on Saturday. Removed three nuts with a nutdriver, unplugged the old icemaker, plugged in the new one and replaced the three nuts. I went from order to ice in the bucket in about 24 hours. Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lois from Thomasville, AL
- Parts Used:
- WP2196157
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Water tubing was accidentally broken from the back of the freezer.
Removed the two screws holding the funnel in place...removed the old one and replaced it witht he new tubing...screwed screws back in and the jov was complete. It actually took longer to get it out of the sack than it did to put it together
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Norcross, GA
- Parts Used:
- 4317943
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Won't make ice cubes.
Removed bottem screw and loosened two top screws. Removed icemaker from support screws and disengaged cable. Replaced in reverse order. Total time was about 15 minutes.
Great DIY experience. Ordering the part was easy and delivery was very fast. Simple installation and had my first cubes in apprximately 15 minutes.
. . . thanks!
Great DIY experience. Ordering the part was easy and delivery was very fast. Simple installation and had my first cubes in apprximately 15 minutes.
. . . thanks!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mike from Camas, WA
- Parts Used:
- WP2196157
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Poor design leaves fitting vulnerable to damage. Part was broken when pushed to close to the wall.
Simply removed the old and replaced with the new part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christopher from Valley Village, CA
- Parts Used:
- WP2196157
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Movers broke the icemaker water fill tube shoving my refrigerator through the front door.
I unscrewed the fill tube screws from the back of the fridge, and pulled the tube out.
Then I put the new tube in, screwed the screws back in and reconnected the waterline.
Then I put the new tube in, screwed the screws back in and reconnected the waterline.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Glessner from Spring Hill, KS
- Parts Used:
- 4317943
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Ice maker tank leaking
I removed one screw from lower portion of unit and loosened 2 top screws. Lifted unit to slide off top screws and unplugged unit. Plugged in unit and positioned unit on 2 top screws. Installed bottom screw and tightened top 2 screws. Repair complete.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Raymond D. from Farwell, MI
- Parts Used:
- 4317943
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
heater didn't thaw ice, stripped eject gears! no ice!!!
added lowering clips to brackets, plugged it in,
hung on sidewall. Plug in power, turned water on,
had ice in an hour. The written directions could be a little more detailed..I am very satisfied with the ease of installation.
hung on sidewall. Plug in power, turned water on,
had ice in an hour. The written directions could be a little more detailed..I am very satisfied with the ease of installation.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from Greensboro, NC
- Parts Used:
- WP2196157
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Old tube had cracked due to being frozen....
I followed the simple steps outlines in the great video! Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- greg from shalimar, FL
- Parts Used:
- 4317943
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
replaced ice maker
three screws and a plug in and it was done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph A from Sachse, TX
- Parts Used:
- 4317943
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Icemaker not working properly
The icemaker was an exact duplicate of the one in my refrigerator. I installed the correct shutoff bar on the icemaker and removed the tab for the water fill spout. After pulling the power cord I loosened the two top screws with a nutdriver and removed the bottom screw. I pulled the icemaker from the rear wall, away from the fill spout, and disconnected the wire harness. Installation was just the reverse of the removal.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from Scottsdale, AZ
- Parts Used:
- 4317943
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Icemaker quit working
I removed the 3 screws that held the unit in place and disconnected the power supply from the front part of the icemaker. I then assembled the replacement icemaker and plugged it in to power supply. I then mounted it with the 3 screws that it required. (Tip): Note the top 2 screws do not need to be totally removed just loosen them enough to remove icemaker. I then cycled the iemaker shutoff arm several times and within 45 minutes I had my first ice cubes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sandford from South Toms River, NJ
- Parts Used:
- 4317943
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
ice maker stopped working
I ordered the replacement ice maker on a Saturday, received it on the next Tuesday, and in stalled it in a little over 15 minutes. Very quick, very easy. Partselect.com was easy to use and exceeded my expectations on every issue. Thanks.
Was this instruction helpful to you?
Thank you for voting!