KRFF302EBS02 Whirlpool Refrigerator - Instructions

Shut off water supply. filter is located in the upper right hand corner of the refrigerator on the inside. open the drop-down door. by hand pull the filter downward. then twist it to the left one quarter turn. it should pull out. I replaced it with a filter bypass plug. you can purchase a high quality filter to replace.it don't buy cheap filter.I made that mistake! hope this helps good luck!

I came across this site and looked at the diagrams. Instead of buying a new crisper bin frame, I noticed that the crisper bin frame was missing the frame brace. I purchased the frame brace and installed it in the crisper frame, which was easy to push into the slot. This solved my problem. No more sag!!

AS PER A VERY GOOD VIDEO I FOUND SIMPLY BY SEARCHING FOR THE PART NUMBER. IT MAY HAVE BEEN ON THIS SITE. SADLY, THE PUSHING ON THE CONNECTOR WITH THE 1/2" WRENCH LOOKED A LOT EASIER IN THE VIDEO, OTHERWISE EASY PEAZY AND I HAVE VERY PAINFUL ARTHRITIS IN MY SHOULDERS.

Removed the freezer door, by loosening 4 screws and pulling upwards to disengage door from frame. Removed the top basket by pulling up on both slides on the gear shaft sides, note they have retaining tabs you must push in. once the slide / guards are up the top basket comes out. Remove the bottom basket. Remove to angled screws on the top tracks and remove. Remove 6 screws on bottom slides, 3 per side and slide out as a whole unit. Unplug the ice maker, remove 3 screws for it to come out. Note I cleaned mine while it was out with vinegar to remove the mineral build up on it. Remove the screws in the back panel, and pull it forwards. The top vent has 2 clips that hold it in and you will need to remove it prior to fully removing the plate. The plug for the icemaker needs to be removed also. Pull the back plate out. Once the plate is out you can see the fan and access it. Unplug the clips that hold the wiring harness secure. 2 screws to remove the fan assembly. Once fan assembly is out, disassemble it, then reverse assemble it with new parts and fire it up. Mine took right off and running like its brand new.

Just slipped it in. I think it's a very poor design.

I'm a 37 year old woman who has never worked on a fridge before, ever.
I was able to google how to run diagnostics on it and determine what the issue was.
Once I received the part I was able to take apart the freezer to get to the motor. Remove the old motor and install the new motor.
This was extremely easy I watched a couple of the youtube videos provided here and now it's running just fine.

It snapped into place

Replaced seal on door. Same problem. Went to Lowe's and got several magnetic cabinet door catches. Attached them to the top of the door. (they can be seen sticking up), with the magnet part screwed to the door and the metal plate attached to a small wooden block glued to the top of the body with contact cement. Cost abound $16.

"To infinity and beyond."

Ordered and placed in the freezer under ice machine.

Thanks for the video showing how to replace the Humidity Slide the knowledge that the end with the flair needed to be slightly bent to SNAP into place was a big help.

Opened the bottom freezer door and pulled the gasket out of the groove. Pulled it out around the door and put the new one back around the door and the pressed into the groove. There was one place that a flat spot didn't take shape so I used a blow dryer to heat it up some and now it seals perfectly.

Killed the power to the fridge. Then, used a small, thin screwdriver to depress the clip on the bottom of the switch and wriggled the old switch out. The two wires easily came off the contacts with pliers. Connected the wires to the new switch and snapped it into the hole--clip facing down and contacts facing up. Turned the power back on and checked the switch. Worked perfectly! Easy job.

Complete replacement of the plastic drawer.

I left this broken rail hang off my refrigerator for almost a year I finally decided to investigate the possibility of ordering the part on line. I found the part on line in minutes and when I received the part it literally took me 3 minutes to install.

backout one screw, push mullion up and free from upper and lower slotted tabs, disconnect one electrical connector. Reverse the steps to reinstall. Literally took 2 minutes.