KRFF305ESS02 Whirlpool Refrigerator - Instructions

Took out the bottom drawer, removed one hexhead nut on the unit, unplugged the unit, plugged in the replacement unit, screwed in the hexhead screw, replaced the drawer, that's it! Very user friendly.

After watching a couple of YouTube videos I had an idea of what to expect. It is really easy. Simply pull out the old, clean up the track and press in the new. I used a heat gun to eliminate the wrinkles in the material. A hair dryer would work as well.

We removed the old switch, unplugged it, plugged the new one in and it was easy to do. But when we tried to put the switch back in we had a very hard time doing it. Eventually got it in, but if it had not been for the difficulty we had getting the new switch to snap in to place, it would have taken under 5 minutes.

Removed old seal and installed new one. Whole job took less than ten minutes. Repair video made it very easy to do! Be sure to allow proper relaxation of new seal before install.

Removed the 2 screws holding the light bulb shield, then the 4 uolding the metal panel. Unplugged the olw door switch and replaced.
reassembled the pieces.

Parts delivered quick. 15-20 minute repair time. Just needed to remove a few shelves, then screws to remove damaged parts and replace with new. Very easy repair.

The repair was pretty simple once we had the new one:

Unpacked new gasket and used a little heat in places to straighten it out.

Removed old gasket
just started at one corner by pulling out of groove and went around the door till all of gasket had been removed from the groove around the door.

Installed new gasket
Inserted into groove on one corner and then went around the door until all of gasket had been inserted.

Closed door and checked that there was good coverage all around the door.

Very simple--Just remove all drawers, remove old end cap, remove slider from old end cap and put on new one. Screw on new end cap and replace drawers. Took about 10 minutes.

It was quit simple. I removed the draw and the shelves above the pantry unit. Once everything was removed (2min), I removed the one side pantry bracket ( 2 screw's). Put in the new pantry bracket and screw's and I was done. I'll give it ten minutes total. easy button Thank you

First, I took out the glass tray along with the two slide out compartments that are part of that assembly. Then I used a small socket set to take out the three screws that hold the part in place and along with the part a plastic connector comes out with it that adjusts the temp of the bin area. Line up the holes on the slider and two screws come out that hold the slider to the part. Disconnet the plastic piece in the back that adjusts are flow (press down plastic holders) Reattach the slider, snap the plastic piece on the back and reassemble. Sounds complicated but once you are in there, its self explanatory.

Replaced the rail and slide baskets. Also readjusted the basket. This was extremely easy and saved me close to $500

This is a bottom freezer refrigerator. Had to remove the freezer door and bottom shelve to make access to the ice maker possible.. Removed the old ice maker using a 1/4" nutdriver to loosen, but not remove, the top 2 screws. Removed the bottom support screw completely.. Detached the wiring harness from the freezer connector and lifted the ice maker up and out of the freezer. Installed the replacement ice maker in reverse order, slipping it over the loosened top screws. Tightened them, making sure the usit was level, then inserted and tightened the bottom support screw . Plugged the wiring harness into the freezer connector.. Unit produced ice within 3 hrs. .

A jar was dropped on the chef's pantry lid and cracked the lid. I unhinged one side of the lid from the pantry drawer by gently pushing outward on one of the hinge pins. The lid slid out easily. I then reversed the process using the new lid and it went in smoothly. Be sure to align the lid so it rests on the shoulder of the pantry drawer. Simple task, no tools, and less than 5 minutes effort. The replacement part was perfect.

I broke the glass in the frig and found partselect and ordered the new glass and had it in 2 days. Very fast shipping.

Remove back cover
Remove drip thing from top to tray in the back
Remove fan motor assembly. This is squirrely. Top bends towards you, bottom pushes in to the unit. Not fun.
CAREFULLY remove copper tube that rests on drip tray
Remove tray - there are clips in the front that get released by screwdriver
Clean up
Replace new tray
Replace copper tube
Play with fan motor assembly till it fits. It doesn't look like it's gonna work until it does. See youtube videos on this.
Replace drip thing from top to tray - I forgot this one the first time.
Replace cover.

This is a simple, but squirrely, repair. Right on the border of easy (because so few tools and steps) and A Bit Difficult because of the patience required.