MSBH30V7LS4 Uni Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- ELIZABETH from HENRICO, VA
- Parts Used:
- 242010901
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Wrong Part sent!!!!!
I did not do a repair. You sent the wrong part & I didn't open the package but I can't get hold of anyone to return the part and get the correct part.
I am very upset that no one will help me. I paid $ 37.28 for the part I ordered and then the wrong part was sent
The sku # on the package is 242010901.This is a roller type part and I ordered a small wheel.
I can't even find a return address to send it to.. Please help me
Elizabeth Romage
libbieinrichmond@comcast.net
8042627963
I am very upset that no one will help me. I paid $ 37.28 for the part I ordered and then the wrong part was sent
The sku # on the package is 242010901.This is a roller type part and I ordered a small wheel.
I can't even find a return address to send it to.. Please help me
Elizabeth Romage
libbieinrichmond@comcast.net
8042627963
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Littleton, CO
- Parts Used:
- 241894223
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
freezer section upper shelf slide assy broken, captive ball slides fell out
Remove frozen food and ice cubes to coolers so they stay frozen.
Remove shallow wire shelf.
Slide out both sides of slide assemblies. Defective slide unclip the front corner front frame remembering to remove the plastic retention rivet first. It has a centre pin that needs to be pulled out first. Support the rest of the frame on the bottom shelf/basket frame
There is one cap head square driver screw to remove on the wall of the freezer holding the slide in place. Leave the other two flat head screws alone. Slide the defective frame off the other two flat head screws. Take new part and attachment is the reverse of the disassembly you have just done. The front frame corner clip is a bit difficult to put together there is a top and bottom spring clip then the plastic "rivet" where you need to push in the centre pin to retain it in the joint. [a bit flimsy so be careful].
The shallow basket should be carefully placed on the front and side clips, and make sure everything is square. Then slide the shelf to make sure it goes into the freezer properly. Then you can re-load the food and ice cubes.
Remove shallow wire shelf.
Slide out both sides of slide assemblies. Defective slide unclip the front corner front frame remembering to remove the plastic retention rivet first. It has a centre pin that needs to be pulled out first. Support the rest of the frame on the bottom shelf/basket frame
There is one cap head square driver screw to remove on the wall of the freezer holding the slide in place. Leave the other two flat head screws alone. Slide the defective frame off the other two flat head screws. Take new part and attachment is the reverse of the disassembly you have just done. The front frame corner clip is a bit difficult to put together there is a top and bottom spring clip then the plastic "rivet" where you need to push in the centre pin to retain it in the joint. [a bit flimsy so be careful].
The shallow basket should be carefully placed on the front and side clips, and make sure everything is square. Then slide the shelf to make sure it goes into the freezer properly. Then you can re-load the food and ice cubes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Hampton, NH
- Parts Used:
- 5304537408
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
Previous seal had a tear and cold air was leaking around seal
Pulled the old seal out of the groove. Placed new seal in the groove. New seal has to be heated and massaged to get it into proper form so it does not leak. I have been continuously heating and massaging to get the seal to get it in the proper form. Been working on it for a week. Almost there.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Lexington, SC
- Parts Used:
- 5304537408
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
THE GASKET LOCKING INSERT DID NOT FIT THE BOTTOM OF THE DOOR.
I REMOVED THE OLD GASKET BEING VERY CAREFUL TO SEE EXACTLY HOW IT CAME OFF. I INSERTED THE LOCKING INSERT INTO THE TRACK IN THE DOOR WHICH DID NOT FIT AS THE OLD ONE DID. AFTER USING TREMENDOUS FORCE WITH MULTIPLE TOOLS I DID MANAGE TO GET THE TOP AND THE SIDES TO LOCK INTO PLACE AND EVENTUALLY HOLD. THE BOTTOM OF THE GASKET DID NOT HOLD SO I USED CLEAR CAULK AND TAPE TO HOLD THE GASKET IN UNTIL THE CAULK CURED. AFTER THE CAULK CURED THE GASKET HAS, SO FAR, REMAINED TIGHT.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- fred from Austin, TX
- Parts Used:
- EAFCBF
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
routine maintenance
slide old filter out and insert new one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Culver from RHINELANDER, WI
- Parts Used:
- 241894224
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The little plastic bàlls came out of old part
Just took old one off and installed new. The company was great to work with.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donna from POUGHKEEPSIE, NY
- Parts Used:
- 241894224
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Balls fell out so I needed a new slide
Basically took the broken piece off and put the new one on after removing the part on the new assembly I didn't need to replace ( It was still secure on the freezer) just popped that bad boy on
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from TUCSON, AZ
- Parts Used:
- 240505801
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Light not turning on when door opened
Used a flat head screwdriver to pop out the old switch, removed the contacts and placed on the new switch, popped the switch back in. Done in about 2 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bernard from NEW WINDSOR, NY
- Parts Used:
- 241779401
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
1 Broken plastic mullion hinge. Mullion was not operating correctly.
Removed screw on Mullion so that the replacement hinge can slide onto the small plastic bracket on the door. Slid the mullion on the hinges and screwed in muliion (1 screw).
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from BRAINTREE, VT
- Parts Used:
- 218755402
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 1- 2 hours
A set scew was ordered twice.
The first order arrived in a huge box and there was no scew to be found, the box had wholes in it. I was given a refund and told to order again.
The repair did not happen and the set screw which was actually recieved the second time was returned because it was the wrong size.
The repair did not happen and the set screw which was actually recieved the second time was returned because it was the wrong size.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patrick from Penryn, CA
- Parts Used:
- 240505801
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Light switch prevented door from closing.
The switch prevented the door from closing about 5 years ago. So I just taped the switch down, and lived without a fridge light for the last 5 years. Painful! And wasteful (food spoiled because we couldn't see it.) Thought I was out of luck, assuming light switches were all the same, got fed up again, and pulled out old switch,,and searched the net for the part number, and just started calling the manufacturer. I got this website after no luck in calling, and took the step to order...and in no time, got it replaced, and we cam see now! It feels like we got a new fridge!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Springfield, MO
- Parts Used:
- 240505801
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
the refrigerator door was hard to close, and upon inspection I finally decided that the light switch was making the door hard to close.
I removed the door actuated light switch with my index finger and thumb on my right hand. I then removed the two wires from the switch. I noticed that the new switch had different look to it,I think Frigidaire must have had a problem with the original design of the switch. Reassembly was just replacing the two wires and putting the new switch in place, and no more door closing problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- EDWIN from ELWOOD, IN
- Parts Used:
- 5308000010
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
loud noise fan blade broke,off balance
take 1/4 hex screws out clean out dust ,remove old fan blade replace with new install bolts .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Greg from henrico, VA
- Parts Used:
- 241639502
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Socket set
The new motor mount screw holes were not threaded.
I had to tap the screw holes with a 8/32 tap so that the screws would not bind.
Was this instruction helpful to you?
Thank you for voting!