HMG651587 Sharp Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- William from Milford, MA
- Parts Used:
- 833697
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
freezer and food section too warm
removed lower back cover. diconnected fan ass'y electrical connection, removed fan housing (3 screws). removed fan motor from housing. cut old connector from fan and installed on new fan with wire nuts included. re-installed new fan to housing and re-installed housing to frame.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kevin from COVINGTON, LA
- Parts Used:
- 833697
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
refrigerator stopped cooling due to condenser over-heating
Pull refrigerator out to access back, unplug unit and remove the 3 .25" screws cut the power leads to motor and install new with easy to understand instructions provided with new motor. Plug refrigerator back in and enjoy your cold beverages once more. EASIEST REPAIR EVER.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Violet from LAKELAND, FL
- Parts Used:
- 61005626
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Wrench (Adjustable)
water flow not functioning properly
repaired by following the video instructions. the video is a great how to do it yourself tool !!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RALPH from PARAMUS, NJ
- Parts Used:
- W11396033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Refrigerator lamp not functioning
Had to push the light switch to get lamp to light up.
Removed power from refrig. and removed old light switch
and replaced with the one I got from Partselect. Turned power back on and was done.
Removed power from refrig. and removed old light switch
and replaced with the one I got from Partselect. Turned power back on and was done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Curtis from Sedona, AZ
- Parts Used:
- 833697
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Motor noise while running and clicking when shutting off
The instruction sheet supplied with the new motor described the steps to take very good. Replaced the rubber grommets for the three motor mounts also. A flashlight or light source was needed or was very helpful.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Al from Tonka Bay, MN
- Parts Used:
- 833697
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
Condenser Fan Failure
Partition between Freezer and Fridge was running very hot. (Warm is normal). Oiling fan did not work. The only problems encountered in the replacement were getting fan out and in through coolant lines, cut plug off to accomodate generic fan wiring, getting the screws back in without cooking your hand on a hot compressor. Unit works great!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- arnie from buffalo grove, IL
- Parts Used:
- 12001991
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
replace solenoid in ice maker
directions in package really made it easy. Saved $175.00
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Clay from Collierville, TN
- Parts Used:
- 12001991
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Socket set
Ice/water dispenser wouldn't work
The repair was really simple - I followed the directions provided. I removed the screws holding the cover in place - unplugged the wiring harness - removed the solenoid and replaced with the new solenoid and door amd reassembled the parts. I wasn't sure if the solenoid was bad since the door was actually broken. I was able to test just using the new door - then replace the solenoid. It was all done in less than 30 minutes. Directions provided were GREAT.
Was this instruction helpful to you?
Thank you for voting!
Clearing an ice jam resulted in a broken ice chute door
This is an easy repair and doesn't take hardly any time, once you can identify the electrical bridals to disconnect and the position of the new ice chute door interface point with the solenoid.
The supplied directions are complete but were quite a bit blurry. The more general dissasembly which is effectively 5 screws and two electrical bridals to remove/disconnect is straight forward. Pay particular attention to the mounting point of the ice door interface with the solenoid. I did it twice because I didn't align the door properly the first time:-)
Much too easy a job than to "call the guy."
The supplied directions are complete but were quite a bit blurry. The more general dissasembly which is effectively 5 screws and two electrical bridals to remove/disconnect is straight forward. Pay particular attention to the mounting point of the ice door interface with the solenoid. I did it twice because I didn't align the door properly the first time:-)
Much too easy a job than to "call the guy."
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Shrewsbury, MA
- Parts Used:
- W11396033
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Broken light switch
Pried out the old switch and installed the new switch.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Justin from Huntersville, NC
- Parts Used:
- W11396033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Light hinge broke
Repair was tremendously easy. All I did was remove old light switch by prying out with screw driver and plugging in the new light switch and pushing it into the hole. Simple! The instructions weren't needed, but they were very thorough.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from Brunswick, GA
- Parts Used:
- 12001991
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Door to Ice Dispenser was broken
First removed the grill from the fountain. Then removed the 2 screws, raised the escutcheon up and off the fountain assembly. Disconnected the power connection to the escutcheon and laid it aside. Removed the 3 screws holding the fountain assembly and disconnected the power supply from it. Removed the broken door pieces. Removed the 2 screws from the solenoid and replaced with new one and replaced the screws. The instructions said to rotate the spring counter clockwise 1/2 turn but I had to rotate it a full turn (to make the door tight when it closed) and insert the end of the spring in the opening of the fountain bracket. Insert the solenoid plunger into the recess of the door strike (the diagram in the instructions helped because this was the part that was broken and I could not figure out where it went). Then I installed everything back the way I had taken it apart.
I am a 61 year old woman and pretty good at taking things apart and putting it back together. My husband usually lets me fix things because I have more patience than him.
I would like to thank parts select for their packaging of the parts and the included diagram.
I am a 61 year old woman and pretty good at taking things apart and putting it back together. My husband usually lets me fix things because I have more patience than him.
I would like to thank parts select for their packaging of the parts and the included diagram.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Bel Air, MD
- Parts Used:
- WP61004888
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
motor wore out making loud noise
unplug the refrigator, remove everything from
frezer compartment. remove ice maker three screws and un plug. remove rear panel 4 screws
remove motor bracket from rear panel 4 screws
unplug motor . replace motor and reasemble in
reverse order. the new motor is very quiet.
frezer compartment. remove ice maker three screws and un plug. remove rear panel 4 screws
remove motor bracket from rear panel 4 screws
unplug motor . replace motor and reasemble in
reverse order. the new motor is very quiet.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- dale from MOGADORE, OH
- Parts Used:
- 12001991
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
ice cube chute door would not open
I just followed the directions that came with the part and it was very simple. Saved at least $100 on the repair. Anyone could do this repair. Don't call Maytag.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Belhaven, NC
- Parts Used:
- 833697
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
cooling fan quit
Ordered new fan motor on line took out old motor and replaced with new one
Was this instruction helpful to you?
Thank you for voting!