7MI2569VEM10 Maytag Refrigerator - Instructions

R & R Icemaker Assembly. Took out 3 screws and unpluged Icemaker & replaced with new part. very easy and the service from PartSelect was fantastic.
Very Satisfied,
Ron Martin

After lots of internet exploring and diagnosis, the icemaker comes right out, and with three screws out and in, the job is all but done. Don't pay anyone for this repair!!!!!

Looking at the ice maker it is pretty cut & dried as to how to remove the unit. I took out the ice tray and just started removing all the mounting screws. The same for the mold ice tray & heating element. I was just sad that you did not have just the heating element separate from the mold ice tray.

The ice mold has a coating on it. Over time the coating deteriorates. If your ice maker leaks water into the ice reservoir inspect the mold to see if the coating is compromised. If so, replace with new.

Remove the ice maker assembly. 3 small hex screws. Unplug power cord. Disassemble ice maker assembly. Remove ice mold/heater. Replace with new. Reassemble.

These guys had my part mailed in lighting fast! It arrived in 2 days in a padded box in perfect shape.The price was the best on line and they saved my life one day before thansgiving!! They got my vote and respect! Great job partselect!!! walt , crete illinois

I called the installer of my filter unit and he told me that often, thhe fridge filter is the problem. Like magic it worked

I pulled the ils gasket out of track and replaced with the new one. Instructions ncluded state to be very careful with new gasket as the magnets may break. Total time 2 minutes with no tools required.

just like the video showed, removed the cover parts inside the fridge, disconnected the water tube inside and pulled out from the top of fridge, then inserted new water tube.

This safety glass is very fragile... it broke under its own weight into a million pieces because I held it just near one edge... I ordered the part through Parts Select that evening and had it in my hands in less than 36 hours!!! Installation only required putting it back in the refrigerator.... Service and price from Parts Select was nothing short of amazing... especially considering that this 5 sq ft piece of fragile glass had to be shipped without breaking! Thanks for great service!

Just pulled out theold and squeezed in the new. I forced it and it went in.

Could not figure out why this was happening suddenly. Then remembered I had recently changed the lid to one I had stored for over two years in the garage. They had sent me a replacement lid when the unit was less than a year old because the origianl had a crack in the clear section. Noticed it seemed a little warped. Thought I would replace it to see if that solved the
problem.
We had to replace the side panel of the draawer because the warped lid had broken the peg off of one side. I didn't want that to happen again.
The new lid did the job....This company is the only one I will use in the future for my appliances. Very easy to find parts and the pricing was better.

Replaced ice bin complete with wheel. Easy fix and resonable.

It was a very simple operation and was done in no time.

Doing it myself saved me at least $100.00 or more.

I was very happy and satisfied with the part and how doing it myself saved me a lot of time and money.

The lining of the ice mold (Whirlpool) started flecking off (black flecks in the ice cubes), so I decided to replace the mold.
Loosen the two 1/4 inch upper nuts and remove the lower nut to remove the ice maker from the freezer. The hardest part was getting it unplugged. I used a small blade screwdriver to release the catch on the connector and pull it out.
Remove the ice maker front cover. If you have a skinny enough phillips screw driver, there are two deep set screws through two holes on the lower portion of the control module (otherwise, remove the three screws on the controller, unlatch the shut-off arm from the control module, and separate the controller to access the mold screws). Unhook the shut-off wire from the end of the tray. Unscrew the two screws holding the mold and remove the mold.
Remove the plastic hardware from the old mold and install on the new mold.
Attach the new mold on to the control module.
WARNING WARNING WARNING!!! The mold I bought already had the alumilastic on it for the contact point to the thermostat. When I installed it and tightened the screws, the alumilastic was dried out, didn't squash down, and dented the bi-metal thermostat on the controller, ruining it. I had to buy a new thermostat. Be sure to check that the alumilastic is pliable. If not, take it off and buy some fresh to put on there.
Re-install the ice maker. It took a while to get the first batch of ice because the ice maker was at room temperature and I had the freezer door open for several minutes. So the freezer had to get cold and the ice maker had to chill down. Once everything got cold, it started making ice again.

I broke the left side end cap the holds the pantry door on.
I search the internet for the part and happened to run across part select. I order the part and received the part with in 3 business days. It took less than 30 minutes to replace the end cap.

The great reviews help me with my choice to order the part from part select. I will order parts from them again.

Thanks for helping me fix my fridge.