MCD2257HEW Maytag Refrigerator - Instructions

Took two times getting the correct part, however after getting the correct part it took about 10-minutes to replace. Had to take the fan out. When you put the new drip pan in make sure it is positioned so that the guides on the pan aligns with slots in the bottom refrig brace, otherwise back pannel will not align correctly. The fan is very easy getting aligned in the new tray. May take a little effort. I do not know why the pan on a refrighterator that is less than 5-years old could start breaking into many pieces.

I changed out the water valve behind the refrigerator that controls when the ice maker and water dispencer receives water. It was easy. I removed the lower back panel to get access to the valve. Pulled the hoses out by pushing up on the ring between the valve and hose and the hose came right out. I disconected the power lines. Of course the water was disconected and power plug out prior to starting the job. I replaced the valve and reconnected the lines and power. I put the back panel back in place and turned the water on to check for leaks. The next day I had ice in the ice maker.

I used board levers to do one side at a time.Kinda tricky, but you can hoist up fridge high enough to replace wheels. take your time think it out and be safe . Make sure you use saftey boards to support load to protect yourself==good luck A small mirror may help to see how the rollers alien in the supports.

The new Ice Maker Assembly arived in less than 24 hours. I was amazed that it came so fast.

I had already removed the old ice maker in order to get the modle number.

I just took two parts off of the old ice maker and quickly snapped them into place on the new ice maker. Then attached it to the refrigerator in less than 10 minutes. With in a few hours I had ice again !!!!!

I would definatly use partselect.com again.

It's good to note, first, that the dual water valve on Amana fridges are notorious for cracking and leaking, either due to the fridge being left in the cold (the water inside the valve freezes and expands, cracking the water valve) or from issues related to shipping. Read the reviews, here - it's a common issue, but easy and cheap to fix yourself. Here's my steps. I first turned off the water source to fridge by closing the correct valve. Next, I unplugged the fridge from electrical and from the water source line. When looking at the back of the fridge, I unscrewed the bottom left cover plate from the fridge body. After unscrewing and removing the plate, I made sure to note which lines came from which areas of the fridge and where the lines ended up at the dual water valve, and how they were routed through the plate and into the valve. The way this fridge is setup, the water source line screws into a main line that heads to the top of the fridge where the water filter is (like a "line in"). There's another line that heads back down to the bottom of the fridge (line out). The "line out" inserts into the outside plug of the dual water valve. The two lines coming out of the dual water valve are different sizes. Make sure to note which line goes to the icemaker and which line goes to the water dispenser inside the fridge. Once I knew which lines needed to go where, I grabbed my empty bucket, pulled the water lines out of the dual water valve with some pliers, and emptied the water into the bucket. After cleaning up any water splatter with my dry towels, I unscrewed the dual water valve from the plate. Once the old dual water valve was removed, I replaced it with the new valve and screwed it back into the plate. I cut off just a bit of the water line ends that were damaged due to pulling with the pliers, and then inserted them back into the correct spots on the dual water valve. I screwed the plate back into the fridge, reconnected the water source line (make sure to use some kind of water sealer tape or putty), plugged the fridge back into the electrical socket, turned the water source valve back on, and waited for leaks. No leaks! Once I was convinced there weren't any leaks, I had to bleed the water lines for about 20-30 minutes (it takes FOREVER...) by putting my bucket under the water dispenser inside the fridge and holding the water button for what seemed like an eternity - until the water was streaming steadily out of the dispenser. Voila! Good as new! Keep in mind that I didn't go through ALL the minute parts of each step - that would take too long. I'm believing that you'll be perceptive enough to catch the small things like looking at how the lines are routed into the dual water valve and where things are screwed into. Use your BRAIN, and you'll be fine. :-)

With the repair parts ordered and received from PartsSelect.com, I was able to install a new Ice Bucket and the crushed ice agitator assembly. This simple repair has the refrigerator dispencing ice like new.

Begin by turning off the water source from the wall, next using a line wrench, remove the brass water line fitting nut from the copper water line from the wall. Next remove the second water line from the plastic push fitting by depressing the fitting to release the water line. Remove the Styrofoam insulation piece that resides between the water lines that run into the refrigerator, then pull the old filter head out. Reverse steps for installation.

I removed the plastic cover from the top hinge and loosened the screws. The magnet seal kept the door in place so I removed the top hinge and tried to lift the door off the bottom hinge but the water line wouldn't let it go. Since I don't use the water feature, I just cut the water line and lifted the door off. That's when I discovered the hinge pin was actually broken off, not just the cam. I went ahead and replaced the cam kit and put it temporarily back together, got right back on line and ordered the bottom hinge. The service was again very fast and in a couple of days I received the bottom hinge, repeated the whole process again and this time replaced the bottom hinge assembly, put some petrolium jelly on the cam kit and now it works smooth and perfect.

I pulled the whole unit(condenser&overload relay)
with my hand & disconnected the wire connected
to it & Replaced it with the new one.Peace of cake.

Took longer to move food from door to inside fridge & take grandkids' artwork off door, & then put it all back than it did to replace cam.
1. Used phillips head to undo 1 screw holding cover over top bracket; lifted off cover.
2. No need to have someone hold door while you remove top bracket; magnets in door gasket will hold it tight to fridge. Used socket to remove 3 screws in top bracket & lifted bracket up off top of door.
3. Door's not heavy. I stood on a sturdy chair to get better leverage. Opened the door enough to break the magnetic seal & llfted it up off bottom bracket. I moved it over just enough to get to the cam, rested the bottom of the door on the floor, & leaned it up against the open front of the fridge to help preserve chilled food.
4. Removed the 1 screw holding in the bad cam to the bottom bracket (uses smaller socket than screws on top bracket).
5. I checked part that goes up inside bottom of door & it was fine, so did not replace it.
6. Trickiest part: putting the door back on. I put a hand mirror on floor by the right corner & facing up so I could see the underpart of the door as I lifted it eased it down on the right place.
7. Closed door, made sure it was straight, replaced top hinge & cover, food, & artwork.

Remove bottom panel in freezer side to get access to the coil.Remove old heater element and defrost thermostat.Installed new hearter and thermostat.Screw back bottom panel re-start frige.

Thanks to parts.com showing the schematic the repair was very easy. Note if the buttons fro dispensing water/ice break you need to order two parts. 1. dispenser Facade and 2. Dispenser facade Insert. To replace do the following. remove the catch tray at the bottom of facade. remove the two screws on the bottom and gently pull bottom of insert out and down. Next unsnap the two wires on the selonoid switch. Next pull down on the harness connector from the printed ckt. Next remove small phillips screw that secures the ckt to the insert and gently pry the six plastic clips that hold the ckt to the insert and remove. Next, install the ckt into the new insert and reconnect the selonoid switch. Next, install the insert back on the door. Next, install the Dispensor Facade sticker over the switch buttons taking care that it is aligned properly. Thats it ready to use.

Turned the old one to unseat and replaced with a new one in the reverse order.

It was great. We replaced the thermistor A little difficult to get to the thermistor but once we found it five minutes. My refrigerator seems happy but we will monitor it and see.

I unplugged the fridge. Loosened the 2 top screws on the ice maker and removed the lower screw. I disconnected the wiring harness and removed the Ice maker. I removed the plastic timer cover in front. I then loosened the screws on the face of the ice maker and removed the broken ice stripper and replaced it with a new one. Re-tightened the screws on the face, installed the timer cover, plugged in the wiring harness, re-attached the ice maker. Plugged the fridge back in and walla, it was making ice in 30 minutes!