CTL1911GEW Magic Chef Refrigerator - Instructions

1)pry out the old/defective light rocker switch with a screw driver (flat head) and pull out the cables 2)unplug two connectors at the end of light rocker switch 3) connect new light rocker into two connectors 4)push the wires inside and put back new light rocker switch

I did exactly as the video showed. I popped out the old switch, disconnected the two terminals, connected the new switch and put it back. The light now works! The refrigerator is over 25 years old and the switch works! What a great website this is. Couldn't of done the job without Partselect's help.

unplug power! Remove the screws from lower panel on back of refrigerator. Lift wire mount out of back panel. Capacitor is mounted directly to the relay and overload switch located on the left side of the compressor. Remove the spring clip holding the capacitor in place and pull the old capacitor out. Plug in new capacitor and replace spring clip. Use vacuum to remove dust from drip pan and wipe fan blades clean. Replace wire into slot on back panel and replace screws. Remove front coil cover below freezer door. vacuum dust off coils and replace cover. Plug refrigerator in and enjoy cold beverages. Relay and overload kit were not required for this repair.

First I did the thermostat and then I did the temperature control valve and I think that did it I should of done the control knob first because the fan in the freezer would run continually and wouldn't even shut off manually with the switch but now it turns off so I happen its fixed

Pulled socket out of housing, unplugged it from source, plugged in new socket and replaced the socket into housing, screwed in bulb and it worked!!

Simply stick a putty knife between the switch and refrig wall. Pop out old swith, remove both wires by pulling off switch by terminals. Throw switch out. Put wires on new switch and push into slot and all done. Nothing to it! Took me 5 minutes if th

Just removed old trim and attached new trim by hand. good results. Happy with your product and tmeliness of delivery Thanks Doug Salter

I love how easy it was to find out what part I needed by seeing the photos to verified it was the part I needed. The repair was super easy and the directions were easy to understand. I didn't even need tools.

I tried to remove the old light switch using a putty knife and a hammer. It was hard to compress the plastic tabs to pull it back through the hole, but all of a sudden, the lights came on. I guess banging on the switch freed-up the contacts. The new switch is now a spare part in case I need it.

followed the video as instructed. Saved two repairman calls, one to find the problem, one to install. Net savings was about $130.00

After receiving the new part almost immediately,using two screw drivers, removed the broken switch from the plastic frame. Be careful not to scratch or otherwise tear the plastic...very pliable. Since the original switch was factory installed and the wires were packed in fiberglass insulation, the switch came out but the wires and clips were still in place and could not reach the new switch. It was necessary to pull them down with bent long nose pliers...used a lot of "pull" but the wires held up.Connected the switch, turned the power on and there was light! Reports from other users really took the uncertainty out of the task.

The fan motor was burned up affecting the efficiency of the refrigerator. I removed the fan motor, tested it, ordered a new one and installed. saved 100 bucks in service call charge and got great service in delivery from parts direct. Ordered on Thursday and recieved monday.

removed old mount with allen wrench replaced with new mount

After thinking it would be impossible to find the parts I needed to fix my old refrigerator I found PartSelect.com. I was surprised that not only did they carry the parts but all were in stock. The actual repair was as easy as the ordering. For the shelf retainer bars and end caps I just put the ends on the bars and snapped it into the door. Care should be taken not to try to bend the end caps too much to insert into the door or they will break at the inside of the bar. They are only thin plastic. I actually bought two spares for future if needed. For the crisper drawer shelf support I used my 1/4" nut driver and removed the piece of the old support with the screw and installed the new one. Do not over tighten the screw or you might a: strip the hole out the sheet metal screw goes in or b: damage the new support or both.

This is an easy fix, simply remove and replace. What I was impressed with is that a how to video was provided along with my part. I wish all manufactures would offer this, the video was easy to understand and you had a good view of the operation. Thanks, a job well done.