CTL1911GEW Magic Chef Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Joe from West Henrietta, NY
- Parts Used:
- 67764-1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Supports inside of refrig. broke, two on right side.
Removed the Crisper drawers and shelf. I then used a nutdriver to remove the broken supports, and installed the new supports using the same screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Destin, FL
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
light switch would not work
Popped the old one out with a kitchen knife and popped the new one back in. It tool less than 15 seconds!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from Billings, MT
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Wrench set
non-functioning refrigerator lite switch
My owners manual said to unplug fridge from elec outlet, use a kitchen knife to gently pry off the switch plate
(manual had a pictoral example), unclip the two wire, replace with on new switch and replace the switch. Close
door and plug back in. Open door to check that the lite
works. Walla! It did. Thanks!
Sincerely, Ron Marshall, Billings, MT
(manual had a pictoral example), unclip the two wire, replace with on new switch and replace the switch. Close
door and plug back in. Open door to check that the lite
works. Walla! It did. Thanks!
Sincerely, Ron Marshall, Billings, MT
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jackie from Nova, OH
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Switch was not working after a repairman had fixed something else
Please bear in mind I am 65 years old & it was harder to get up & down off the floor then to change the switch. Was very easy - watched video, unplugged unit. I used the putty knife at the right front corner to work loose, when it came loose had to loose the left side a little. The unit pulled out easily. detached the wired that had a single plug with 2 prongs on it. Attached the plug, pushed new switch into place. There was no way you could place wires on wrong prong. When done, plugged refrigerator back in & checked if working. I CAN SEE THE LIGHT and the food in the freezer now. Thank you for making an easy repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dora from Rock Island, IL
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
light would come on and off
Viewed the viedo - it showed what to do
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- michael from Hoffman Estates, IL
- Parts Used:
- WP61002112
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken End Cap
Simply replaced part. Press fit shelf retaining bar back into place. I was just glad you had this obscure part which was easy to find on you website.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Williamsport, MD
- Parts Used:
- W11045462
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lower shelf holder kept falling out
Removed keeper on left side, slid trim into keeper on right, attached left keeper to trim, re-inserted keeper onto door.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fred from Concord, NH
- Parts Used:
- WP61005339
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
freezer was cold but fridge compartment was not
Removed fan shroud in center of plastic finish cover in back of freezer by unsnapping. Removed back cover in freezer by removing 4 screws with nut driver. Removed power connection from fan motor and removed 2 screws holding fan motor in place with nut driver. Installed replacement motor following steps in reverse. Plugged in fridge and cooling began with fan running.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anthony from Broadlands, VA
- Parts Used:
- 67764-1
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken crisper support
The main issue is that my supports are NOT held on by screws -- they are behind the fridge wall and can not be removed. So this is my solution (ignore the 'fix kit' -- it is useless and is just this part plus a metal screw. It cost me $20 to find this out). Here is what I did: 1) Cut off the old support with a knife. 2) Get a small toggle bolt (I used 1/8" x 2", < $2 from Home Depot) and thread into new support. 3) Dig around in insulation to make sure there is space for toggle to flip open. 4) Install!!!! Wish I'd thought of this before :-)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paula from Rush, NY
- Parts Used:
- W11384469
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
light switch sticking
I watched the video and thought "I can do this". Made some notes and then proceeded to remove the old switch and replace with the new one. Thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from Wasilla, AK
- Parts Used:
- W11384469
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Light switch in the refrigerator was faulty from the first day we installed the fridge.
I had ordered some other parts for something entirely different off your website and service was great. So after almost ten years of a dark refrigerator, because of a defective switch, I decided to see if you had the part to fix it... You did and the part got here in 3 days. I had a working light switch and all the light in the world where my husband needed it most (in the fridge). It took me at the most ten minutes to replace the part. All is well now and I have a happy husband who can find the leftovers just fine. Thanks for your great service!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- thomas from sonoma, CA
- Parts Used:
- WP61002112
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken cap ends
put the end caps on
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Louis from Beloit, WI
- Parts Used:
- W11384469
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- Less than 15 mins
Light did not come on (bad bulb!) on TC18KL
I have never before seen a bulb with the filament intact not light. If the bulb's filament seems intact, screw the bulb into a known working lamp and see if it lights. When screwing it back into the socket in the fridge, it takes a bit of extra effort to fully seat (until it does, it won't light!). For replacing the switch, I unplugged the unit, used a paint scraper and worked it under the switch bezel from the right side. A bit of moxie, and the switch came out. The replacement switch had a different spade contact spacing than the original. I used a pair of scissors to cut the rubber bridge between the two switch wire connectors so I could connect to the new switch. In the end, it turned out to be the bulb. NOTE: The Model TC18KL is _not_ listed! What I finally found that the number "P7803211WL" on the sticker is actually a manufacturing code. Found this out by searching, and Sears' part search came up with matches.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from Glade Hill, VA
- Parts Used:
- WP61006074
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
control was broken
Took the new knob out of the box and popped it in place. The end. EZPZ! quick service and quick repair. Thanks!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Irene from Whitehall, MT
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
No light in frig
We tried repairing with a new switch which was very easy to install but it didn't fix the problem.
Was this instruction helpful to you?
Thank you for voting!