LFC20760ST (AST6LGY) LG Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- ROSEMARY from STOCKHOLM, NJ
- Parts Used:
- 4980JJ1016A, 3551JJ1005X
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The cover assembly was broken
Following the instructions
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William L from SUMAS, WA
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
light didn't come on when the door was opened
I took a very thin bladed screwdriver and took the old part out -carefully.
The new part fit in quite easily.
The new part fit in quite easily.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from HOLLYWOOD, FL
- Parts Used:
- 4975JJ2028C
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broke right freezer rail
Removed old rail by unscrewing 3 screws and put new rail on
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathleen from YUCCA VALLEY, CA
- Parts Used:
- 4775JJ2018A
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
I lost the part in a move.
It was so easy I opened the package and took part right out and put it on the refrigerator and bolted it down and that's it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from CHARLESTON, MO
- Parts Used:
- 6600JB3007B
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Inside light would not go off
Ordered part from part select. Received part with out instructions. It took only one screwdriver for 1 screw removal and then removing cover to replace switch. Pretty simple
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- shirley from ONALASKA, WI
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Light switch for refrigerator not functioning
Followed instructions online
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Calvin from Northome, MN
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Light quit coming on when door opened.
Unplug from wall receptacle. Pry switch out with screwdriver while pushing on inner tab. Then disconnect electrical plug.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from TONAWANDA, NY
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
bad switch
The 2 minute or so video was not exactly matching the model that we had but the instructions were very good and important. The switch was a little difficult to get out from the side of the refrigerator.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Philip from Ashland, MA
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Lights didn't come on when door was opened
I have moderate to good mechanical skills, but getting the old switch out was a sizeable challenge. Since this switch suffered some damage during extraction, I was lucky to have ordered a new one to replace it. Reinstall took approximately 90 seconds. PartSelect saved me an expensive service call.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JON from OJAI, CA
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
INTERIOR DOOR ACTIVATED LIGHT SWITCH QUIT WORKING
1. Unplug the refrigerator (to avoid shock) 2. With one screwdriver pry open the switch on the side facing the door to a gap of about 1/8 inch 3. Insert a second screwdriver into the gap to press the plastic tab back slightly and this should release the part. 4. pull the part out and unplug it, you may have to pry back some small tabs on the sides, 5. Plug in the new switch 6. plug in the refrigerator the light should come on, if not tighten the connection 7. Insert new switch back into its slot, it should snap in place. Done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from STREATOR, IL
- Parts Used:
- MJB63029901, 4430JJ2005B
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Door stopper broke
Very simple, remove broken part with screwdriver and replace with new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fred Lee from BOTHELL, WA
- Parts Used:
- 4980JJ1016A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
The shelf that holds the crisper drawers had cracked and finally broken.
Bought a new shelf. Bought a center support (new), Put the new center support in the shelf. Removed glass, old shelf and drawers. Replaced the broken shelf by hooking the new one in to existing supports. Replaced glass. Replaced drawers.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- SUREN from SAN RAMON, CA
- Parts Used:
- AEQ72909603
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
ice maker stopped working
replaced the ice maker with the new assembly kit, the longest time taken was to fit back the pull out door .. had to align the slots correctly and check that it slid back and forth easily.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cathrine from NEW ORLEANS, LA
- Parts Used:
- MEG54557902
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
The right hand glide for the top freezer drawer was broken.
Replaced the glide.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rita from GROSSE PT PK, MI
- Parts Used:
- 3551JJ1005X
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
Crisper cover broke.
It took me about 20min. Remove glass top and remove old support. Slide new support and glass.
Was this instruction helpful to you?
Thank you for voting!