KBSD606ESS00 KitchenAid Refrigerator - Instructions

Local service person missed the diagnosis and advised $10,000 new refrigerator. I looked and saw that the switch was deformed and had burn marks. Searched for switch online. Found site Ordered. Part arrived next day. 5 minute job to replace. No tools needed. Refrigerator works great. Thank you t!

Isolate the broken LED light fixture by pressing the door switch and releasing it; broken light will remain off and not flicker. Unplug refrigerator and apply painter's tape around the light fixture to protect surface finish from being marred or scratched. Use the putty knife to remove the LED light and disconnect the wiring from connector. Reconnect wire of new part and install by pressing light fixture in place. Remove tape and plug refrigerator back in.

Easy!!!!! Just cut the power to the unit and unscrew the boards. One is to the right of the ice maker and one is to the left. Snap the connecter on the old board so it will disconnect and replace it. It works perfect now. I had a service man come out and he quoted me $400.00. He told me I needed a whole new ice maker too. Not true. I simply email you guys and had the part in 3 days. It only cost me $80.00. I will use your site for every part I need. Thanks

I called a local appliance repair / sales store and he told me what to look for. There is an electronic "eye" on the "On / Off" panel in the freezer, and there is an electronic eye that sends a beam across to the other side where there is a receiver. If there is no beam, or the beam is obstructed --- for example when the freezer door is open the little "door" on the opposite side of the On / Off switch opens, interrupting the beam --- the icemaker will not work. In my case it was easy... there was no beam being sent across, so I KNEW it was bad.

Ordered the part, took out 6 screws total to remove the sender and receiver, removed the circuit boards with 3 more screws, replaced with new boards, and reinstalled.

Trust me - a 10 year old could do this. Don't be afraid because it involves "circuit boards" - it's literally one or two screws, replace the boards, screw them back in, and plug the two sides back in. ANYONE can do it... anyone!!!

Removed the 2 screws holding the light bulb shield, then the 4 uolding the metal panel. Unplugged the olw door switch and replaced.
reassembled the pieces.

We popped out the new filter and replaced the cap with a twist. It was so easy. It is important to vaccum the front of the refrigerator for accumulating dust.

Unpluged the refrigerator, removed the burnt out switch by unpluging it, plugged the new one in re installed the switch into cover. Plugged in refrigerator replaced cover. Done. Easy as one two three

Simply cut the water tube on both sides of connector and push in the new one.

These are instructions are for replacing the see-through covers (manufacturer part number WPW10131132) on the two upper door utility bins.

First it is easiest to remove the entire bins rather than hold open the fridge doors while you work.

There are two plastic studs on the bin body designed to fit through the holes in the bin cover. The tips of these studs will have to be simultaneously compressed with pliers (thus two sets of needle nose pliers) in order to slide the old cover past the studs to remove. Unless you have three hands, you will need another person to slide the cover left past the studs while you are handling both sets of pliers. Although the studs are pretty flexible, be careful not to break them off in the process. Once the cover is past the studs you can pull in free.

installing the new cover is easy. Since the studs are tapered, simply align with the holes on both ends of the the cover with the studs and apply pressure to the right. The cover will slide over the tapered studs and lock into place.

Once the new covers are installed, simply reinstall the complete bin back on the refrigerator door. Just push and snap in the tracks on the refrigerator door interior body.

Unplug power to refridg/freezer. Removed the screw in rt. rear bottom of ice maker to remove. After removing slightly, unplug pigtail. Remove ice maker completely. Remove large square cover from left side to expose motor. Remove screws to remove motor. Replce with new. Replace ice maker to freezer, plug pigtail back in, put screw back in rt rear bottom, plug refridg/freezer back into power source. Ice was making in about 2 1/2 hours.

Referencing the info/schematics you have on your website, I unscrewed/unattached top-front panel (carefully), from behind the panel you have to detach the wires (2) from the switch, pushed "in" the switch to remove, put in new switch and attach wires to test BEFORE remounting panel. Tada!! Thank you PartSelect! You saved me at least $80...would have been at least $100 to have a repair person come to the house!

Repair went well,took about five to ten minutes to disconnect the power from the fridge removed the defective switch installed the new one ,reconnected the power,,,and Let there be light and there was light!

First I had to figure out how to get the old unit out so I could work on it. The three screws that others wrote about were the ones that hold the motor in place. There are 3 screws holding the ice maker in the frame, along with one screw covering the electrical connection. The electrical connection was difficult to unplug because the locking tab was on the back side of the connection and with no room to work in the freezer it didn't become apparent until several frustrating minutes went by. There were no instructions provided, the picture on the ordering page showed the complete ice maker, and for $80 you get a printed circuit board with a small round item which must be the motor/timer control. The two plastic parts for moving the ice from the ice maker were included but not replaced because I didn't notice them until I had finished replacing the ice maker back in the freezer and wasn't going to start over again.
Once installed, there wasn't any noise, even of water flowing like the old one, could not tell if the unit was working or not. In the morning there was new ice in the bin indicating the repair had been successful. This is like anything else, if you have done it before it is a 5 minuter job but when you have to look at it and try to figure it out it takes a bit longer. All in all, it was simple enough, I was expecting a complete ice maker unit like was in the picture when ordered but only the motor module was actually needed.
We have another refrigerator/freezer that has an icemaker that is over 20 years old and has never been repaired, it is a Sears model though, probably made by Whirlpool or someone else.

removed the LED covers on both sides of the freezer, unplugged each circuit board, plugged in both circuits, replaced the LED covers, job complete, making ice

Unplugged power from unit. Removed tray bracket, removed 2 screws from drive motor cover, removed 4 screws from motor assembly, disconnected power from assembly, Replaced rubber seal at the lower end of the recently installed new shaft. Re-connected the power plug, placed the new dispenser assembly into position making sure the shaft was properly seated in the motor. Replace the four screws, plugged in main power and tested the dispenser prior to replacing the ice container. Tightened the screws, replace the cover and the tray bracket.