KRFC400EWH00 KitchenAid Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Pam from CHINO, CA
- Parts Used:
- WP67005930
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The clear lid on my pantry door cracked
I removed the drawers and glass shelf that are over the pantry drawer as well as the small piece that allows the drawer to pull in and out. Then I simply snapped the old one out, snapped the new one in, replaced everything I had removed and Done! Took less than 10 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kevin from SWANVILLE, ME
- Parts Used:
- W11338583
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Freezer Bulb failed
Unscrewed bulb from sock .
Replaced with new one . Now working
Replaced with new one . Now working
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gerald from Grants Pass, OR
- Parts Used:
- WP12656105
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
I broke the pin that holds the lid that covers pantry at the bottom of the fridg.
I removed the drawers above and the glass shelf, then removedthe screws to remove the broken end cap then reversed the proceedure to install the new part. Was simple to do and it works fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charlie from HARRODSBURG, KY
- Parts Used:
- WP12656105
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Broken pin to door
Easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Port Aransas, TX
- Parts Used:
- WP12656018
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
The pin on the right side of the Deli Drawer full width door broke off
I removed the Deli Drawersvegatable and fruit drawers. Removed the glass panel. Removed the screws holding the Endcap and snapped the old one out. A back panel strip that controls the humidity snapped out. I installed the back panel to the new endcap. Installed the new endcap snapping it in place and used the screws to keep it in place.
It was not difficult and everything fit perfectly. The only thing it takes is a little understanding as to how it all fits together. It took about 20 minutes.
It was not difficult and everything fit perfectly. The only thing it takes is a little understanding as to how it all fits together. It took about 20 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Margate, FL
- Parts Used:
- WP12656105
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
pulling the dairy draw out, a plastic knob broke,that keeps the cover on the draw on tight.
after pulling the draw out. had to remove 3 screws on the left side, pull out one part, and then replaced the broken pin. put everything back in place and it was done.perfect job.saved alot of money. thanks to part-select
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Angela from Topeka, KS
- Parts Used:
- WPW10534153
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Refrigerator was missing grille
This grille just snapped into place without the use of tools. Couldn't have been easier. And the delivery was super fast; I ordered online one day and the item arrived the very next day.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janice from Fairfield, OH
- Parts Used:
- WP67005930
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Cracked Deli Tray
I fumbled a large jar of olives that hit the deli tray, inside lining and top of bottom freezer drawer before making it to the floor. The deli tray cracked, a gash was in the white bottom lining and the SS top of freezer drawer was dented. Service and delivery was excellent, fast and installation was a matter of popping the tray cover off and snapping in the new one. Now, if I could only change out the liner myself.........
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Allentown, PA
- Parts Used:
- WPW10312696
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
not making ice
watched video
took me less than 5min. to replace inlet valve.
an cleaned my frig at the same time that took me longer to do.
took me less than 5min. to replace inlet valve.
an cleaned my frig at the same time that took me longer to do.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from CAPE CORAL, FL
- Parts Used:
- WPW10714545
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Gasket was old and air leaking into freezer !
Took off old one and just replaced new, very easy and corrected problems!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rodney B. from Crestview, FL
- Parts Used:
- W11395888
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Filter stopped up. Causing the refrigerator to make a loud noise. water dispenser didn't work. less than 4.00 fixed all that
Shut off water supply. filter is located in the upper right hand corner of the refrigerator on the inside. open the drop-down door. by hand pull the filter downward. then twist it to the left one quarter turn. it should pull out. I replaced it with a filter bypass plug. you can purchase a high quality filter to replace.it don't buy cheap filter.I made that mistake! hope this helps good luck!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from EASTON, PA
- Parts Used:
- W11396037
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
gasket had ripped over the years where they flexed when dooors were opened and closed.
last time i tried it right away after removing from shipping box.. relaxing with with hot air gun... was not to easy... this time i allowed gaskets to relax for a week on a flat surface. in a warm room.... took less than 5 minutes per door.... no hot air needed.... VERY easy.
Was this instruction helpful to you?
Thank you for voting!
Empty box sent with no part!!!! No customer service help because of covid
No product was sent in the box for the shaft I received an empty box from them cannot perform any repairs because I got no product from this company. Called customer service said due to Covid no customer service available when online and receive no customer service no refund no product no help
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Terry from N SYRACUSE, NY
- Parts Used:
- WP12656018
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Dropped a jar onto the pantry and broke the plastic piece on end cap that moved the drawer lid.
Removed the lid and pantry drawer. Removed crisper drawer on right side and glass shelve. Removed 2 screws on glide. Removed 2 nuts with nut driver. Gently tugged on the pantry end cap and it released from the back wall. Had to rotate about 90 degrees to remove the extension off the back wall so I could remove the thermostat control arm from old piece and put it onto the new piece. Gently removed the thermostat control through a series of squeezing pieces and rotations. Do not force anything. Take your time as you are working with plastic that could break at any moment with force. Replace in reverse order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from WALLA WALLA, WA
- Parts Used:
- WPW10300024
- Difficulty Level:
- Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
original ice maker would make ice and then water would over flow into ice bin and freeze
stick the very small screw driver in the hole on the left side cover and lift up to release the keeper tab,pull out to expose the wire connecter.insert the small screw driver in the slot on the left side to release the tab while pulling apart the two connectors.tuck the wires tight to side and pull out the ice maker.I thought I was getting the whole ice maker assembly,but just got a part of it,so I had take it apart and put it back together.the hardest thing to change over was the stop lever arm that senses the level of ice in the bin.after all this,it didn't work at all.not happy around here.back to filling ice trays
Was this instruction helpful to you?
Thank you for voting!