KRFF707ESS01 KitchenAid Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Tom from LONGMONT, CO
- Parts Used:
- W10311524
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Changed air filter
Very simple, easy, and quick! Anybody can do it!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from WISC RAPIDS, WI
- Parts Used:
- W10822606
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Ice Augur Motor not Working
Very easy doit repair. Watched Youtube video helpful. Small nut driver and flashlight the only tools needed. Ordered part with standard delivery and received the new motor in under 24 hours! Impressive. I will use Part Select again! So happy to have a working augur. No more stale ice at the bottom of the bin. No more scooping ice with fingers!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Hemet, CA
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Light switch wasn't working.. As I would close the door I would notice our frig light wasn't going off...
I simply removed the old switch by gently pulling down on the old switch with a screwdriver. When it was about half way out I just gently pulled down on the old switch and it popped out... I removed the two connectors attached to the old switch by pulling on the connectors with a pliers...I tried using my fingers but wasn't able to pull the connectors off so I used pliers. It worked perfectly.. When pulling off the old connectors, make sure you attach the new switch to the same tabs on the new switch... It was very easy to do and took under 5 mins.....The light switch works perfect....P.S. You should unplug the frig while making the connection just in case....Safety first....!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- THOMAS from WILLARD, OH
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
defective light switch
inserted a knife between the switch and the plastic interior in order to pop the switch out.
then took off the 2 wires on the old switch put them on the new switch and reinserted the switch into the plastic interior.
then took off the 2 wires on the old switch put them on the new switch and reinserted the switch into the plastic interior.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Roseville, CA
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door light switch disintegrated
Very simple fix, remove 3 screws, two connectors to the old switch
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- stu from richmond, VA
- Parts Used:
- W11384469
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
fridge door switch did not work
I removed the switch housing (4 screws), replacing the switch in the housing was a snap. It took 5 minutes, cost $8 and light works like new!
Why didn't I order this part and do the repair earlier? Very simple.
Why didn't I order this part and do the repair earlier? Very simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- dorotea from staten island, NY
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Light didnt go on
The light rocker switch wasnt working. I found the part on the web site. It was so easy. I used a screw driver to pop out the old one and pop the new one in. It took 5 min. Thanks!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- anthony from HAVELOCK, NC
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
changed the light bulb still would not work so I figured it was the switch sure enough.
I took a chance and ordered a switch that is next to the top of the door. looked for how to remove it easily done in ten minutes works fine last long time.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Olga from COLLEGE STA, TX
- Parts Used:
- EDR2RXD1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Filterer
Easy
Was this instruction helpful to you?
Thank you for voting!
auger motor was not working in ice maker
I watched some of the you tube videos , the repair went well
just followed the directions the repair took less than 30 mins
just followed the directions the repair took less than 30 mins
Was this instruction helpful to you?
Thank you for voting!
POS fridge is constantly under repair.
Understood the problem by removing the old dispenser first. That made me realize I also needed the shaft. Went online and matched up all the #’s and the repair went smoothly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from WADING RIVER, NY
- Parts Used:
- W10822606
- Difficulty Level:
- Difficult
- Total Repair Time:
- 30 - 60 mins
Ice make auger stopped working
I carefully matched the model number to replacement part cross-reference and ordered the Part.
You-tube instructions were accurate except for the plug wire that prevented removal of the auger motor. It took significant maneuvering to drop the old motor. The new motor fit in better but the male plug configuration did not match the female plug from the refrigerator.
A lot of wasted effort and time as well as expense! What good is matching replacement parts when the replacement is not correct?
You-tube instructions were accurate except for the plug wire that prevented removal of the auger motor. It took significant maneuvering to drop the old motor. The new motor fit in better but the male plug configuration did not match the female plug from the refrigerator.
A lot of wasted effort and time as well as expense! What good is matching replacement parts when the replacement is not correct?
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Virginia from POLSON, MT
- Parts Used:
- EDR2RXD1
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
replaced water filter
Had a hard time getting the refridgerator part of the filter to LET GO. The grooves weren't lined up with the areas meant to pinch. A knife on each side got it to release.
Thanks.
Have a good one.
Thanks.
Have a good one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jorge from ORLANDO, FL
- Parts Used:
- W10407212
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
The rigth door does close tight
I ordered a gasket and follow the instructions, such as warm the gasket, to get it in the door using my fingers, but the door did not close titght enough. The problem could be something else. The initial problem is in there
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ALEXANDER from CROSSVILLE, TN
- Parts Used:
- W10843055
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Refrigerator would work great then after 2 weeks would stop. I had to unplug and wait a few minutes the plug it in again. Would work 2 weeks or so then the exact same thing. Hopefully the main board will solve the problem
(1) Unplug the refrigerator
(2) Remove 4 nut driven sheet metal screw to remove access plate in the back.
(3) Remove a clear hard plastic cover. Several electronic boards are held in place with plastic tabs.
(4) The main electronic board is easily recognizable.
(5) Unplug all wire plugs from main board. Don't work about what plug goes where when reinstalling. Each plug is different from the others. It's fool proof.
(6) I wore vinyl gloves when I handled and installed the new board. I did not want any static charge to jump to the board.
(7) Re-install all electrical plugs. Note use minimum force to remove and install these plugs as some are small and fragile.
(8) Before re-installing the hard clear plastic cover make sure all electrical plugs are properly installed.
(9) Follow thru to reverse removal procedure for metal plate.
(10). Plug in the refrigerator.
(11) I purchased a delay receptable to prevent both electrical surges and reduction in electrical voltage.
(2) Remove 4 nut driven sheet metal screw to remove access plate in the back.
(3) Remove a clear hard plastic cover. Several electronic boards are held in place with plastic tabs.
(4) The main electronic board is easily recognizable.
(5) Unplug all wire plugs from main board. Don't work about what plug goes where when reinstalling. Each plug is different from the others. It's fool proof.
(6) I wore vinyl gloves when I handled and installed the new board. I did not want any static charge to jump to the board.
(7) Re-install all electrical plugs. Note use minimum force to remove and install these plugs as some are small and fragile.
(8) Before re-installing the hard clear plastic cover make sure all electrical plugs are properly installed.
(9) Follow thru to reverse removal procedure for metal plate.
(10). Plug in the refrigerator.
(11) I purchased a delay receptable to prevent both electrical surges and reduction in electrical voltage.
Was this instruction helpful to you?
Thank you for voting!